Xantrex Technology XHR, XFR, XFR3 specs

Features and Specifications

Specifications

Table 1.4 Specifications for XFR 2800 W Series Supply with GPIB Interface Installed (60 V to 600 V)

Models	60-46	100-28	150-18	300-9	600-4
Program Resolution	9.2mV	15.4mV	23.1mV	46.2mV	92.4mV
Voltage	9.2mV	15.4mV	23.1mV	46.2mV	92.4mV
Current	6.44mA	3.92mA	2.52mA	1.26mA	0.56mA
OVP	9.2mV	15.4mV	23.1mV	46.2mV	92.4mV
Program Accuracy1
Voltage	150mV	150mV	225mV	225mV	250mV
	±0.25%	±0.35%	±0.35%	±0.35%	±0.35%
Current	250mA	140mA	120mA	80mA	80mA
	±0.1%	±0.15%	±0.1%	±0.1%	±0.1%
OVP	600mV	800mV	1.5V	3.0V	6V
Readback Resolution
Voltage	9.2mV	15.4mV	23.1mV	46.2mV	92.4mV
Current	6.44mA	3.92mA	2.52mA	1.26mA	0.56mA
Readback Accuracy1
Voltage	150mV	150mV	225mV	225mV	250mV
	±0.25%	±0.35%	±0.35%	±0.35%	±0.35%
Current	250mA	140mA	120mA	80mA	80mA
	±0.1%	±0.15%	±0.1%	±0.1%	±0.1%

1.Apply accuracy specifications according to the following voltage program accuracy example: Set a model 20-130 power supply to 10 volts.

The expected result will be within the range of 10 volts ± 75mV ± 0.12% of the set voltage of 10 volts

16	Operating Manual for GPIB for XHR/XFR Series Power Supply

Image 18

Xantrex Technology XHR, XFR, XFR3 manual Models 60-46 100-28 150-18 300-9 600-4

Contents

GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase Date Safety Supply Main Sections Manual Revisions About This Manual Contents Contents Features and Specifications Description Functions Features and FunctionsFeatures and Specifications Readback Specifications Models 140 12-100 20-60 35-35 40-30OVP Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Introduction Initial Inspection Installation and Configuration Initial Inspection Gpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB Basic Setup Procedure Step # Description Action ReferencePON SRQ IEEE-488 Primary Address Selection Address Power On Service Request PON SRQ Rear Panel SRQ Switch Position PON SRQ StateSwitch Position Power on results Condition Default Settings Model Example Iset Ibfind devname IEEE-488 Controller Connection Internal PCB Jumper Selections High OFF LOW High LOW OFF User Signals User Signals J7 Connector J7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Operation Gpib Operation Example Ascii Power On PON Set when unit Bit Decimal Description Reset By Position WeightRequest Service SRQ Set when LSB Command Syntax Computer EntryFormat Description Form Floating Number Definition Example Iset 2.0A Vset Command Summary CMODE? AUXA?AUXB? DLY? Idata FAULT?Cmode IHI Auxa 1 on Command ReferenceCommand Description Auxb 1 on Changing an output setting Response Fold mode where mode is Snsp Mask None = Unmask ALL Status, and Fault Registers on Accumulated Status, Status, and Fault Registers on SNSP, ALL, None Response Vmax voltage Accumulated Status, Status, and Fault Registers Condition Mnemonic Bit Position Bit Weight Error Codes 11 Error Codes Troubleshooting LEDs Calibration Voltage Program Calibration Procedure Readback Voltage Mode CalibrationSetup Voltage Calibration Current Mode Calibration Current Calibration SetupCurrent Program Calibration Procedure Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc