Manuals / Xantrex Technology / Lawn and Garden / Portable Generator

Xantrex Technology XHR, XFR, XFR3 WARNING Limitations on Use, Information About Your Power Supply

Models: XHR, XFR, XFR3

1 62

Download 62 pages 62.83 Kb

Page 7

Information WITHOUT LIMITING THE GENERALITY OF THE FOREGOING, UNLESS SPECIFICALLY AGREED TO BY IT IN WRITING, XANTREX

a.MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN MANUALS OR OTHER DOCUMENTATION PROVIDED BY IT IN CONNECTION WITH THE PRODUCT; AND

b.ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION.

THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK.

WARNING: Limitations on Use

Please refer to your product user manual for limitations on uses of the product. Specifically, please note that this power supply is not intended for use in connection with life support systems and Xantrex makes no warranty or representation in connection with any use of the product for such purposes.

Xantrex Technology, Inc.

8999 Nelson Way

Burnaby, British Columbia

Canada V5A 4B5

Information

About Your

Power

Supply

Please record the following information when you first open your Power Supply package:

Model Number	______________________________________________
Serial Number	______________________________________________
Purchased From	______________________________________________
Purchase Date	______________________________________________

Release Release 3.1 (2002-06)

Copyright © 2002 Xantrex Technology Inc. All rights reserved. Printed in Canada

Release 3.1

v

Image 7

Xantrex Technology XHR, XFR, XFR3 manual WARNING Limitations on Use, Information About Your Power Supply

Contents

Operating Manual GPIB-XHR GPIB-XFR GPIB-XFR3Page Operating Manual for Programmable DC Power SuppliesLimited Warranty How do you get service?Proof of purchase may be in any one of the following forms Disclaimer Product WARNING Limitations on Use Information About Your Power SupplySupply PowerSafety Warnings Cautions and NotesManual Revisions Main SectionsAbout This Manual About This Manual Operating Manual for GPIB for XHR/XFR Series Power SupplySection Features and Specifications Section Installation and ContentsConfiguration Section Operation Contents Description Section 1. Features and SpecificationsFunctions Features and FunctionsFunctions Readback7.5-140 SpecificationsFeatures and Specifications Models100-12 Features and SpecificationsModels 60-2012-220 Features and SpecificationsModels 7.5-300100-28 Features and SpecificationsModels 60-4620-50 Features and SpecificationsModels 7.5-130150-7 Features and SpecificationsModels 100-10Introduction Section 2. Installation and ConfigurationInitial Inspection Remote Programming LEDs activated. See “Connector J7 User Signals” on pageInstallation and Configuration Initial InspectionFigure 2.2 GPIB Interface Subplate Located on Power Supply Rear Panel Installation and ConfigurationInitial Inspection JUMPER SELECTION Installation and ConfigurationLED INDICATORS Initial InspectionBasic Setup Procedure IEEE-488 Primary Address Selection Remote/Local Operation Power On Service Request PON SRQparticular GPIB controller interface installed on your computer Put the controller in charge by sending an Interface Address the unit devname or device name asInternal PCB Jumper Selections IEEE-488 Controller ConnectionSend commands UNL, UNT, MTA0, LLO in Internal PCB Jumper Selections Figure 2.4 User Signals J7 Connector User SignalsTo install the ferrite block User Signals Installation and ConfigurationFigure 2.6 J7 User Cable with Ferrite Block GPIB Operation Section 3. OperationIntroduction Example Example Then useExample Example Serial Poll In a serial poll, the controller polls each deviceMASK FOLD ≠ MASK FD Command SyntaxMASK FOLD = mask fold MASK FOLD ≠ MK FOLDForm Command SyntaxOperation DescriptionExample COMMAND parameter COMMAND parameter, parameterLFOperation Command SummaryDescription Operation Query CommandsDescription Description Calibration CommandsOperation DescriptionOperation Command Referenceread. See “Accumulated Status, Status, and Fault Registers” on page CommandDescription Commandbeen masked using the MASK command, then the ERR bit in the registers OperationOperation CommandDescription Description Status, and Fault Registers” on page 50. Mnemonics are separated fromCommand OperationOperation switch on the supply. See “Power On Service Request PON SRQ” onStatus, and Fault Registers” on page CommandRegisters” on page “Accumulated Status, Status, and Fault Registers” on pagestatus and fault registers See “Accumulated Status, Status, and Fault CommandOperation CommandDescription Example Accumulated Status, Status, and Fault RegistersBit Weight OperationERROR IDENTIFICATION Error CodesTable 3.11 Error Codes ERROR #LEDs TroubleshootingIntroduction Section 4. CalibrationVoltage Mode Calibration SetupVoltage Program Calibration Procedure Voltage Readback Calibration ProcedureVoltage Mode Calibration CalibrationCurrent Program Calibration Procedure Current Calibration SetupCurrent Mode Calibration Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page 800 667 8422 Toll Free North America prg.info@xantrex.com Xantrex Technology Inc8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 604 422 8595 Tel 604 421 3056 Fax