Xantrex Technology XHR, XFR, XFR3 manual

Features and Specifications

Specifications

Table 1.6 Specifications for XHR 1000 W Series Supply with GPIB Interface Installed (100 V to 600 V)

Models	100-10	150-7	300-3.5	600-1.7
Program Resolution	15.4mV	23.1mV	46.2mV	92.4mV
Voltage	15.4mV	23.1mV	46.2mV	92.4mV
Current	3.92mA	2.52mA	1.26mA	0.56mA
OVP	15.4mV	23.1mV	46.2mV	92.4mV
Program Accuracy1
Voltage	150mV	225mV	225mV	250mV
	±0.35%	±0.35%	±0.35%	±0.35%
Current	140mA	120mA	80mA	80mA
	±0.15%	±0.1%	±0.1%	±0.1%
OVP	800mV	1.5V	3.0V	6V
Readback Resolution
Voltage	15.4mV	23.1mV	46.2mV	92.4mV
Current	3.92mA	2.52mA	1.26mA	0.56mA
Readback Accuracy1
Voltage	150mV	225mV	225mV	250mV
	±0.35%	±0.35%	±0.35%	±0.35%
Current	140mA	120mA	80mA	80mA
	±0.15%	±0.1%	±0.1%	±0.1%

1.Apply accuracy specifications according to the following voltage program accuracy example: Set a model 20-50 power supply to 10 volts.

The expected result will be within the range of 10 volts ± 50mV ± 0.12% of the set voltage of 10 volts.

18	Operating Manual for GPIB for XHR/XFR Series Power Supply

Image 20

Xantrex Technology XHR, XFR, XFR3 manual Models 100-10 150-7 300-3.5 600-1.7

Contents

GPIB-XHR GPIB-XFR GPIB-XFR3 Page Operating Manual for How do you get service? Phone 604 422 Toll Free North America 800 667 Fax 604 421 What does this warranty not cover? Disclaimer Product Information About Your Power Supply Model Number Serial Number Purchased From Purchase Date Safety Supply Main Sections Manual Revisions About This Manual Contents Contents Features and Specifications Description Features and Functions Features and SpecificationsFunctions Readback OVP SpecificationsModels 140 12-100 20-60 35-35 40-30 Models 60-20 100-12 150-8 300-4 600-2 Models 300 12-220 20-130 33-85 40-70 Models 60-46 100-28 150-18 300-9 600-4 Models 130 20-50 33-33 40-25 60-18 Models 100-10 150-7 300-3.5 600-1.7 Introduction Initial Inspection Installation and Configuration Initial Inspection Gpib Interface Subplate Located on Power Supply Rear Panel Gpib Interface PCB PON SRQ Basic Setup ProcedureStep # Description Action Reference IEEE-488 Primary Address Selection Address Switch Position Power on results Power On Service Request PON SRQRear Panel SRQ Switch Position PON SRQ State Condition Default Settings Model Example Iset Ibfind devname IEEE-488 Controller Connection Internal PCB Jumper Selections High OFF LOW High LOW OFF User Signals User Signals J7 Connector J7 User Signal Connector Circuit Block Diagram J7 User Cable with Ferrite Block Operation Gpib Operation Example Ascii Bit Decimal Description Reset By Position Weight Request Service SRQ Set whenPower On PON Set when unit LSB Format Command SyntaxComputer Entry Description Form Floating Number Definition Example Iset 2.0A Vset Command Summary AUXA? AUXB?CMODE? DLY? FAULT? CmodeIdata IHI Command Reference Command DescriptionAuxa 1 on Auxb 1 on Changing an output setting Response Fold mode where mode is Snsp Mask None = Unmask ALL Status, and Fault Registers on Accumulated Status, Status, and Fault Registers on SNSP, ALL, None Response Vmax voltage Accumulated Status, Status, and Fault Registers Condition Mnemonic Bit Position Bit Weight Error Codes 11 Error Codes Troubleshooting LEDs Calibration Voltage Mode Calibration SetupVoltage Program Calibration Procedure Readback Voltage Calibration Current Program Calibration Procedure Current Mode CalibrationCurrent Calibration Setup Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page Xantrex Technology Inc