Manuals / Xantrex Technology / Lawn and Garden / Portable Generator

Xantrex Technology XHR, XFR, XFR3 manual To install the ferrite block

Models: XHR, XFR, XFR3

1 62

Download 62 pages 62.83 Kb

Page 33

Image 33

Installation and Configuration

User Signals

Figure 2.5

J7 User Signal Connector Circuit Block Diagram

J7 Cable Use a standard 8-position telephone jack and data cable to connect to J7. Add a Connection ferrite block to reduce radiated emission. The one inch square ferrite block with

built-in housing clip is packaged and shipped with the power supply interface card.

To install the ferrite block:

1.Position the block no more than 5 cm (2") from the power supply end of the J7 user cable.

2.Open the ferrite block housing.

3.Loop the cable through the ferrite block. See Figure 2.6, “J7 User Cable with Ferrite Block” on page 32.

4.Close the housing clip.

The ferrite block ensures that the power supply system meets radiated emission requirement 89/336/EEC for CE mark approval. See the power supply's operating manual for noise specifications.

Release 3.1

Page 33

Image 33

Xantrex Technology XHR, XFR, XFR3 manual To install the ferrite block

Contents

Operating Manual GPIB-XHR GPIB-XFR GPIB-XFR3Page Operating Manual for Programmable DC Power SuppliesLimited Warranty How do you get service?Proof of purchase may be in any one of the following forms Disclaimer Product WARNING Limitations on Use Information About Your Power SupplySafety PowerWarnings Cautions and Notes SupplyMain Sections Manual RevisionsAbout This Manual About This Manual Operating Manual for GPIB for XHR/XFR Series Power SupplyContents Section Features and Specifications Section Installation andConfiguration Section Operation Contents Description Section 1. Features and SpecificationsFunctions Features and FunctionsReadback FunctionsFeatures and Specifications SpecificationsModels 7.5-140Models Features and Specifications60-20 100-12Models Features and Specifications7.5-300 12-220Models Features and Specifications60-46 100-28Models Features and Specifications7.5-130 20-50Models Features and Specifications100-10 150-7Section 2. Installation and Configuration IntroductionInitial Inspection Installation and Configuration activated. See “Connector J7 User Signals” on pageInitial Inspection Remote Programming LEDsInstallation and Configuration Figure 2.2 GPIB Interface Subplate Located on Power Supply Rear PanelInitial Inspection LED INDICATORS Installation and ConfigurationInitial Inspection JUMPER SELECTIONBasic Setup Procedure IEEE-488 Primary Address Selection Remote/Local Operation Power On Service Request PON SRQparticular GPIB controller interface installed on your computer Put the controller in charge by sending an Interface Address the unit devname or device name asIEEE-488 Controller Connection Internal PCB Jumper SelectionsSend commands UNL, UNT, MTA0, LLO in Internal PCB Jumper Selections Figure 2.4 User Signals J7 Connector User SignalsTo install the ferrite block Installation and Configuration User SignalsFigure 2.6 J7 User Cable with Ferrite Block Section 3. Operation GPIB OperationIntroduction Example Then use ExampleExample Example Serial Poll In a serial poll, the controller polls each deviceMASK FOLD = mask fold Command SyntaxMASK FOLD ≠ MK FOLD MASK FOLD ≠ MASK FDOperation Command SyntaxDescription FormExample COMMAND parameter COMMAND parameter, parameterLFCommand Summary OperationDescription Query Commands OperationDescription Operation Calibration CommandsDescription Descriptionread. See “Accumulated Status, Status, and Fault Registers” on page Command ReferenceCommand Operationbeen masked using the MASK command, then the ERR bit in the registers CommandOperation DescriptionCommand OperationDescription Command Status, and Fault Registers” on page 50. Mnemonics are separated fromOperation DescriptionStatus, and Fault Registers” on page switch on the supply. See “Power On Service Request PON SRQ” onCommand Operationstatus and fault registers See “Accumulated Status, Status, and Fault “Accumulated Status, Status, and Fault Registers” on pageCommand Registers” on pageCommand OperationDescription Bit Weight Accumulated Status, Status, and Fault RegistersOperation ExampleTable 3.11 Error Codes Error CodesERROR # ERROR IDENTIFICATIONLEDs TroubleshootingIntroduction Section 4. CalibrationVoltage Program Calibration Procedure Voltage Readback Calibration SetupProcedure Voltage Mode CalibrationVoltage Mode Calibration CalibrationCurrent Calibration Setup Current Program Calibration ProcedureCurrent Mode Calibration Current Readback Calibration Procedure Over Voltage Protection OVP Calibration Page 8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 Xantrex Technology Inc604 422 8595 Tel 604 421 3056 Fax 800 667 8422 Toll Free North America prg.info@xantrex.com