Manuals / Brands / Computer Equipment / Power Supply / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology XTR 850 Watt, XTR6-110, XTR8-100, XTR12-70, XTR20-42, XTR33-25, XTR40-21, XTR60-14, XTR80-10.5, XTR100-8.5, XTR150-5.6, XTR300-2.8, XTR600-1.4, XTR6-220, XTR8-200, XTR12-140, XTR20-84, XTR33-50, XTR40-42, XTR60-28, XTR80-21.5, XTR100-17, XTR150-11.2, XTR300-5.6, XTR600 Local Lockout

1 274

Download 274 pages, 2.9 Mb

Local Operation

3-30 975-0200-01-01

Local Lockout

Local lockout is a feature that allows the front panel to be locked so that

accidental button presses are ignored. This feature is often used to lockout

the front panel when you are controlling the power supply from a remote

location. When in local lockout mode, the front panel will display LOCL

Loc whenever a button is pressed or a knob is turned.

Enabling Local Lockout

To enable local lockout:

1. Turn the mode control knob to the PGM position or press the Rotary

knob/Enter button if the control knob is already at the PGM position.

The display will show rE in the output voltage display and the

selected remote interface in the output current display.

2. Turn the Rotary knob/Enter button until the display shows LOCL

Loc.

3. Press the Rotary knob/Enter button.

4. Turn the Rotary knob/Enter button until the display shows LOCL On.

5. Press the Rotary knob/Enter button.

Local lockout has been enabled.

The SCPI command (s) for these instructions are:

[:]SYSTem:REMote:STATe

Disabling Local Lockout

To disable local lockout:

1. Turn the mode control knob to the PGM position or press the Rotary

knob/Enter button if the control knob is already at the PGM position.

The display will show rE in the output voltage display and the

selected remote interface in the output current display.

2. Turn the Rotary knob/Enter Button until the display shows LOCL

Off.

3. Press the Rotary knob/Enter button.

Local lockout has been disabled.

The SCPI command (s) for these instructions are:

[:]SYSTem[<channel(s)>]:REMote:STATe

Contents

Main Page Page About Xantrex Trademarks Notice of Copyright Exclusion for Documentation Date and Revision Page Page About This Manual Purpose Scope Audience Conventions Used Related Information Acronyms Font Conventions Important Safety Instructions Power Supply Safety Markings WARNING: High energy and high voltage WARNING: Limitations on use CAUTION: For use as a battery charger Standard Warnings Contents Important Safety Instructions 1 2 Introduction 3 Local Operation 4 Analog Programming (APG) and Isolated Analog Programming (ISOL) 5 Remote Operation 6 Calibration and Troubleshooting A SCPI Command Reference Page Page Figures Page Table s Page Page Features and Options XTR 850 Watt and XTR 1700 Watt Models Front Panel for XTR 850 Watt and XTR 1700 Watt Front Panel Display and Controls Figure 1-2 Front Panel Display and Controls Rear Panel Connectors on XTR 850 Watt Page Rear Panel Connectors on XTR 1700 Watt Figure 1-6 Figure 1-7 XTR 1700 Watt Series: 6 V to 40 V Models XTR 1700 Watt Series: 60 V to 600 V Models Page Basic Setup Procedure Basic Setup Procedure Step 1: Inspecting and Cleaning Initial Inspection Periodic Cleaning Step 2: Location and Mounting Rack Mounting Purchasing Rack Mount Kits Venti lati on Step 3: Connecting AC Input Power XTR 1700 Watt AC Input Connector XTR 1700 Watt AC Input Wire XTR 1700 Watt AC Input Wire Connection Page Step 4: Selecting Load Wires Load Wiring Insulation Rating Current Carrying Capacity Page Step 5: Performing Functional Tests Poweri ng the Power S upply On/Of f Voltage and Current Mode Operation Checks Step 6: Connecting Loads DC Output Connectors 6 V40 V Models 60 V600 V Models Inductive Loads Connecting Single Loads Connecting Multiple Loads Step 7: Connecting Remote Sensing Page Page Page Configuring Settings from the Front Panel Using the 9-Position Mode Control Knob Using the Rotary knob/Enter button Coarse and Fine Adjustment Modes Fine adjustment mode Pressing the Rotary knob/Enter button to change the mode to fine Select and Set from the Front Panel Navigating the Menu System Setting VOL and CUR Modes Page Normal Display Mode and Inactivity Timeout Navigating the Menu System 975-0200-01-01 3-7 Figure 3-2 Front Panel Menu System Display Messages on the Front Panel Front Panel Display Text Table 3-2 Front Panel Display Text Standard Operation Operating Modes Constant Voltage Mode Operation Constant Current Mode Operation Automatic Mode Crossover Page Page Shipped Configuration (Local Operation) Turning the Output On/Off Turning the Auxiliary Output On/Off Output Auto Start Mode (Auto Restart) Auxiliary Auto Start Mode Alarms and Errors Clearing Alarms Clearing Triggered and Manual Alarms Clearing a Flash Failure Alarm Clearing Automatic Alarms Front Panel ALARM LED Alarm Masking Alarm Output Latching Setting Foldback Mode Resetting Activated Foldback Protection Using Over Voltage Protection (OVP) Defining the OVP Set Point Using Under Voltage Protection (UVP) Defining the UVP Set Point Over Current Protection (OCP) Using Over Temperature Protection Lock (OTP) Defining the OTP Mode Resetting in Latch Mode Current Configuration Memory Settings User Setting Memory Locations Saving User Setting Memory Locations Recalling User Setting Memory Locations Local Lockout Enabling Local Lockout Disabling Local Lockout Using the External Shutdown Function Activating the External Shutdown Function Controlling the External Shutdown Function Defining the Polarity of the External Shutdown Signal Page Interlock Function Defining the Interlock Mode Power On Status Signal Hardware Malfunction Alarms Resetting the Power Supply Page Using Multiple Power Supplies Page Using Multiple Power Supplies 975-0200-01-01 3-39 Configuring Multiple Supplies for Series Operation Power Supply Connecting to the Load in Local Sensing Mode Figure 3-5 Series Operation Connecting to the Load in Remote Sensing Mode Configuring Multiple Supplies for Current Sharing Operation (APG Method) Setting up the Master Unit Setting up the Slave Units Note: The slave unit discussed here is not the same as the remote interface Page Page Page Page Analog Programming (APG) of Output Voltage and Output Current Remote Programming Options Analog Monitor Signals Auxiliary Outputs Page Analog Programming (APG) Connector J1 Figure 4-1 APG Connector Terminals Table 4-3 APG Pins and Functions J1 Table 4-3 APG Pins and Functions J1 Making Control Connections Wiring Analog Programming Mode Analog Programming With External Voltage Source J1.9 J1.7 J1.10 J1.7 Voltage-Controlled Voltage APG Setup Activating APG Voltage Mode Deactivating APG Voltage Mode Query for Analog Voltage Input Level Page Voltage-Controlled Current APG Setup Activating APG Current Mode Deactivating APG Current Mode Query for Analog Current Input Level Page Page Resistive-Controlled Voltage APG Setup Deactivating APG Voltage Mode Query for Analog Voltage Input Level Page Resistive-Controlled Current APG Setup Deactivating APG Current Mode Query for Analog Current Input Level Voltage and Current Readback Isolated Analog Programming Mode (ISOL) AUX Output and Isolated Analog Programming (ISOL) Connector Table 4-4 AUX Output and ISOL Connector Pins and Functions J3 CAUTION: Equipment damage Making ISOL Control Connections ISOL Programming With External Voltage Source Voltage-Controlled Voltage ISOL Setup Activating ISOL Programming Voltage Mode Deactivating ISOL Voltage Mode Query for ISOL Voltage Input Level Voltage-Controlled Current ISOL Setup Activating ISOL Programming Current Mode Deactivating ISOL Current Mode Query for ISOL Current Input Level Analog Programming With External Resistor Resistive-Controlled Voltage ISOL Setup Activating ISOL Programming Voltage Mode Deactivating ISOL Voltage Mode Query for ISOL Voltage Input Level Resistive-Controlled Current ISOL Setup Activating ISOL Resistive-Controlled Current Setup Deactivating ISOL Current Mode Query for ISOL Current Input Level Voltage and Current Readback (Isolated) Query Remote Control Source State V V Page Page Hardware and Connection Setup Configuring Remote Control Using RS-232 Figure 5-1 Remote Control Connectors Table 5-1 Remote Control Connector Pins and Functions J4 and J6 RS-232 Communication Cable with RJ-45 to DB-9 RS-232 Communication Cable with RJ-45 to DB-25 Completing the Setup Configuring Remote Control Using RS-485 RS-485 Communication Cable with RJ-45 to DB-9 RS-485 Communication Cable with Two RJ-45s Completing the Setup Configuring Remote Control using the USB Connector Setting Up the PC to Use the USB Connection Installing USB to Serial Converter and Serial Port Page Page Verifying Installation Page Complete the Setup Ethernet (ENET) or GPIB Connector (Optional) Multiple Power Supply Connections to RS-485 Bus Multiple Power Supply Setup Note: If either RS-232 or RS-485 are used for communication with the Multiple Power Supply Connections to ENET Terminal Configuration Data Format End of Message HyperTerminal Setting up a HyperTerminal connection Page Page Selecting the Appropriate Communication Port Data Rate Setting (bps) Multichannel Address Setting Remote Interface Addressing Multichannel Commands Explained Status Reporting in SCPI Page Status Registers Model from IEEE 488.2 Status Byte Error/Event Queue (ERR) Questionable Status Register Summary (QSR) Message Available (MAV) Standard Event Status Summary (ESB) Master Summary Status (MSS) Request Service (RQS) Operation Status Register Summary (OSR) Query the Status Byte Standard Event Status Register (SESR) Standard Event Status Enable Register Standard Event Status Register Page Operation Complete Wait-to-Continue Command Remote Operation 5-32 975-0200-01-01 Standard SCPI Register Structure Figure 5-21 SCPI Register Model OPERation Status Register 975-0200-01-01 5-33 OPERation Status Register Figure 5-22 Operation Status Register Fanout Page Current SHare Sub-Register Operation Status Register Commands Query Operation Status Register Event Query Operation Status Register Condition Enable Operation Status Register Set Operation Status Positive Transition Filter Current Sharing Sub-Register Commands Shutdown Sub-Register Commands Protection Sub-Register Commands Set Protection Negative Transition Filter QUEStionable Status Register QUEStionable Status Register 975-0200-01-01 5-41 Figure 5-23 SCPI QUEStionable Registers Fanout VOLTage Sub-Register TEMPerature Sub-Register Questionable Status Register Commands Query Questionable Status Register Event Query Questionable Status Register Condition Enable Questionable Status Register Voltage Status Register Commands Temperature Status Register Commands Set Temperature Status Negative Transition Filter SCPI Error/Event Queue Querying For the Errors Querying For the Error Code Only Querying For the Number of Errors in the Queue Reset Command Clear All Status Registers Clear Status Command SCPI Preset Status Command Line Help System Querying Help for all Command Headers Page Querying Help for Legacy Command Headers Querying Help for Command Syntax Page Locking and Unlocking the Front Panel Auto Sequence Programming Setting Dwell Time Storing an Auto Sequence Program: Saving an Auto Sequence Program to File: Readback and Troubleshooting an Auto Sequence Program: Reloading an Auto Sequence Program: Running an Auto Sequence Program: Repeating an Auto Sequence Program: Page Configure Other Protection Mechanisms Foldback Protection Setting the Foldback Mode Over Temperature Protection Interlock Enable/Disable Save and Recall Set Analog Programming Level Set Remote Programming Interface Protection Mask (Enable Alarms) Page Page Main Voltage and Current Calibration Principle Understanding the Problem Step 1: Gain Calibration Page Calibrating the Output Voltage Gain Calibration Offset Calibration Calibrating the Output Current Gain Calibration Offset Calibration Over Voltage Protection Calibration Non-isolated Analog Programming Calibration Non-isolated Voltage Monitoring Calibration Non-isolated Current Monitoring Calibration Non-isolated Voltage Programming of Voltage Calibration Non-isolated Resistive Programming of Voltage Calibration Non-isolated Voltage Programming of Current Calibration Non-isolated Resistive Programming of Current Calibration Page Calibration Procedure for Isolated Modes Isolated Voltage Monitoring Calibration Isolated Current Monitoring Calibration Isolated Voltage Programming of Voltage Calibration Isolated Resistive Programming of Voltage Calibration Isolated Voltage Programming of Current Calibration Isolated Resistive Programming of Current Calibration Storing and Loading Calibration Parameters Restore Factory Calibration User Diagnostics Emergency Shutdown Unusual or Erratic Operation Troubleshooting for Operators Page Page SCPI Conformance Information Codes and Standards IEEE 488.2 Requirements SCPI Requirements IEEE 488.2/SCPI Syntax and Style SCPI Command Hierarchy Using SCPI Commands Using Minimum and Maximum Using Queries Terminating Characters Common Commands Parameter Types Boolean Parameters Discrete Parameters Numeric Parameters String Parameters SPCI Command Tree 975-0200-01-01 A-9 SCPI Command Reference A-10 975-0200-01-01 975-0200-01-01 A-11 SCPI Command Reference A-12 975-0200-01-01 975-0200-01-01 A-13 SCPI Command Summary Table A-1 IEEE 488.2 Commands (Continued) Table A-2 IEEE 488.2 Commands (Continued) Table A-1 Readback Commands Table A-3 Table A-3 SCPI Commands for Output Control (Continued) Table A-4 SCPI Commands for Calibration Table A-4 SCPI Commands for Calibration (Continued) Table A-4 SCPI Commands for Calibration (Continued) Table A-5 SCPI Commands to Clear All Protection Mechanisms Table A-7 Table A-6 SCPI Commands for Foldback Protection Table A-8 Table A-7 SCPI Commands for Triggering Table A-9 System Commands Page Page Page Table A-10 Table A-9 Status Commands Page Page Page Page Page Page Page Table A-11 Protection Commands Table A-12 Auto Sequence Commands Table A-12 Auto Sequence Commands (Continued) Page Page Error Messages Command Error List B Execution Error List Device-Specific Error List B Query Error List Page C C-2 975-0200-01-01 Electrical Specifications for XTR 850 Watt Table C-1 XTR 850 Watt Electrical Specifications for 6 V to 600 V Models 975-0200-01-01 C-3 Electrical Specifications for XTR 850 Watt AC Line Input Specifications for XTR 850 Watt Tabl e C- 1 The input to the power supply requires the following input specifications. XTR 850 Watt Electrical Specifications for 6 V to 600 V Models C-4 975-0200-01-01 Electrical Specifications for XTR 1700 Watt Table C-2 XTR 1700 Watt Electrical Specifications for 6 V to 600 V Models 975-0200-01-01 C-5 Electrical Specifications for XTR 1700 Watt AC Line Input Specifications for XTR 1700 Watt The input to the power supply requires the following input specifications. C-6 975-0200-01-01 Remote Operation Table C-3 Remote Operation Common Specifications for All Models C-8 975-0200-01-01 975-0200-01-01 C-9 Figure C-1 XTR 850 Watt Mechanical Dimensions: 6 to 40 V Models C-10 975-0200-01-01 Figure C-2 XTR 850 Watt Mechanical Dimensions: 60 V to 600 V Models 975-0200-01-01 C-11 Figure C-3 XTR 1700 Watt Mechanical Dimensions: 6 V to 40 V Models Page 975-0200-01-01 C-13 Figure C-5 XTR 1700 Watt Mechanical Dimensions: 60 V to 600 V Models Page Warranty and Product Information Warra nty What does this warranty cover? This Limited Warranty is provided by Xantrex Technology Inc. What will Xantrex do? Xantrex will, at its option, repair or replace the defective product free of How do you get service? If your product requires troubleshooting or warranty service, contact your Disclaimer Product Exclusions Return Material Authorization Policy Return Procedure If you are returning a product from outside of the USA or Canada In addition to the above, If you are returning a product to a Xantrex Authorized Service Center (ASC) A Xantrex Out of Warranty Service Information About Your System Index Numerics A C D G I J L M T U W X