Yamaha AW 16G 1, 2, 3, 4, 5, 6, 7

Mixdown and bounce operations

■Adjusting the effect send level

Here’s how to load an effect library into internal effect 1,

and adjust the level (effect send level) of the signal that is

sent from each channel via effect bus 1 to internal effect

1Repeatedly press the [EFF1] knob or hold

down the [EFF1] knob and use the CURSOR

[ ]/[ ] keys to access the LIBRARY page of

the EFF1 screen.

2Select the effect library that you want to use,

and load it into internal effect 1.

In this example, we will select a reverb-type library.

3Press the [EFF1] knob once to access the

SEND page of the EFF1 screen.

If insert effect 1 is connected via the mixer section

send/return, the following items will be added to

the SEND page of the EFF1 screen.

1EFF

Adjusts the send level of the signal that is sent from

each channel to insert effect 1.

BPRE/POST

Selects the location from which the signal from

each channel will be sent to insert effect 1. Move

the cursor to this area and press the [ENTER] key to

switch between the following two settings.

PRE (pre-fader).......... The signal from immediately

before the fader will be sent.

POST (post-fader)...... The signal from immediately after

the fader will be sent.

Note

If the page you see is different than shown above, make

sure that track channels are selected as the object of your

operations. (This is shown in the upper left of the screen.)

If input channels/pad channels are selected, press one of

the [TRACK SEL] keys.

4Move the cursor to the PRE/POST ﬁeld in the

screen, and press the [ENTER] key to specify

the location from which the signal will be

sent from each channel to internal effect 1.

Select POST if you want the volume of the effect

sound to be affected by the fader position. Select

PRE if you want to set the volume of the effect

sound independently of the fader position.

5While you play back the song, move the cur-

sor to the EFF knobs in the screen, and adjust

the level of the signal that is sent from each

channel to internal effect 1.

Tip!

Another way of adjusting the send level to internal effect

1 is to press a [TRACK SEL] key to select a track channel,

and then turn the [EFF1] knob of the Selected Channel

section. This method is convenient if you want to adjust

the effect level without displaying a different screen.

6To adjust the master level of the effect send,

repeatedly press the Selected Channel sec-

tion [VIEW] key or hold down the [VIEW] key

and use the CURSOR [ ]/[ ] keys to access

the BUS page of the VIEW screen.

The BUS page of the VIEW screen lets you use on-

screen faders to adjust the master level of each bus.

1PEAK button

This is an on/off switch for the peak hold function of

the level meters. If this button is on, a peak indica-

tor will show the level meter peaks, and will

remain displayed. To reset this indicator, you can

temporarily switch the PEAK button off. This setting

is shared with the METER page of the VIEW screen.

BPRE/POST button

This selects whether the level meters of the BUS

page will indicate the pre-fader level (PRE) or the

post-fader level (POST). This setting is independent

from the METER page of the VIEW screen.

CAUX

DEFF

EBUS

Use these faders to adjust the master levels of AUX

buses 1/2, effect buses 1/2, and the L/R bus. The

level of each bus is indicated by the level meters at

the right of each fader.

7Move the cursor to the fader for effect bus 1,

and use the [DATA/JOG] dial to raise or lower

it.

Tip!

You can also adjust the level of the return signal that is

returned from the internal effect to the mixer section. For

details, refer to “Editing the parameters of an internal

effect” (

→

p. 94).

132 4 51