1

• Phone jacks

 

• Kopfhörerbuchsen

 

• Prise de casque

 

• Tomas de auricu-

• Cardboard packing cushions

lares

• Kartonformstücke

 

 

• Cales d’emballage en carton

 

• Amortiguadores de embalaje la

 

caja de cartón

AC power cord

Netzkabel

Cordon d’alimentation

Cable de alimentación de CA

5 x 18 mm screws x 30

Schrauben (5 x 18 mm) x 30

Vis de 5 x 18 mm x 30

Tornillos de 5 x 18 mm x 30

CVP-98/96: Assembly

Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the se- quence given below.

Assembly should be carried out by at least two persons.

Be sure to use the correct screw size, as indicated above. Use of incorrect screws can cause damage.

Be sure to tighten up all screws upon completing assembly of each unit.

To disassemble, reverse the assembly sequence given below.

ZOpen the box and remove all the parts.

Take out the two cardboard packing cushions and place them on the floor. Then take out main unit and place it on top of the packing cushions. Position the cushions so as to protect the phone jacks on the base of the unit.

Remove all parts from the box. Confirm that all parts shown in the illustration above are provided.

When you lift the pedal box assembly, make sure that you lift by both legs.

XCarefully lean the main unit against a wall.

To make it easier to install the legs, place a soft blanket or similar material on the floor near a wall, close the Clavinova keyboard cover, place the front panel of the Clavinova (the side with the keyboard) on the blanket and gently lean the unit against the wall — MAKING SURE THAT IT CAN NOT FALL — as shown in the illustra- tion.

• Do not lay the main unit upside-down on the floor.

CAttach the front legs.

Securely attach the two front legs using three screws for each leg (use a Philips “+” screwdriver) as shown in the illustration. Make sure that the screws are firmly tight- ened.

CVP-98/96: Zusammenbau

Achten Sie darauf, die Teile nicht zu verwechseln, und installieren Sie alle Teile in der richtigen Ausrichtung. Gehen Sie beim Zusammenbau bitte in der angegebenen Reihenfolge vor.

Die Montage sollte von mindestens zwei Personen vorgenommen werden.

Achten Sie darauf, die richtige Schraubengröße zu verwenden, wie es oben gezeigt ist. Die Verwendung der falschen Schrauben kann zu Schäden führen.

Achten Sie während der Montage darauf, bei jedem Arbeitsgang alle Schrauben festzuziehen.

Für die Demontage muß die angegebene Reihenfolge umgekehrt befolgt werden.

ZDen Versandkarton öffnen und alle Teileauspacken.

Nehmen Sie die beiden Kartonformstücke heraus, und legen Sie sie auf den Boden. Nehmen Sie dann die Haupteinheit heraus, und stellen Sie sie auf die abgelegten Formstücke. Positionieren Sie die Formstück dabei so, daß die Kopfhörerbuchsen unten am Instrument nicht beschädigt

werden können. Vergewissern Sie sich, daß alle in der obigen Abbildung aufgeführten Teile vollzählig vorhanden sind.

Halten Sie die Pedalkasten-Baugruppe beim Heben stets an bei- den Beinen.

XDie Haupteinheit vorsichtig an eine Wand lehnen.

Um das Anschrauben der Beine zu erleichtern, breiten Sie eine Decke oder ein weiches Tuch neben der Wand auf dem Boden aus, schließen die Tastaturabdeckung des Clavinova, stellen das Instrument mit der Vorderkante (Seite mit der Tastatur) vorsichtig auf die Decke und lehnen es an die Wand, wie in der Abbildung gezeigt. VERGEWISSERN

SIE SICH, DASS DAS INSTRUMENT NICHT KIPPEN ODER WEGRUTSCHEN KANN!

Legen Sie die Haupteinheit nicht mit der Oberseite nach unten auf den Boden!

CDie vorderen Beine montieren.

Schrauben Sie die beiden vorderen Beine mit jeweils drei Schrauben (Kreuzschlitzschraubendreher verwenden!) gut am Clavinova fest, wie in der Abbildung gezeigt. Ziehen Sie die Schrauben fest an.

46 CVP-98/96/600