•PANPOT changes the value for the melody voice and rhythm voice in relation to the preset value.

•Portamento time is fixed to 0 when the PORTAMENTO CONTROL is used.

•HARMONIC CONTENT applies adjustment to the resonance value that is set by the voice. This parameter specifies relative change with the value of 64 producing 0 adjustment. As values get higher the sound becomes increasingly eccentric. Note that for some voices the effective parameter range is narrower than the legal parameter range.

•RELEASE TIME applies adjustment to the envelope release time set by the voice. This parameter specifies relative change with the value of 64 producing 0 adjustment.

•ATTACK TIME applies adjustment to the envelope attack time set by the voice. This parameter specifies relative change with the value of 64 producing 0 adjustment.

•BRIGHTNESS applies adjustment to the cut-off frequency set by the voice. This parameter specifies relative change with the value of 64 producing 0 adjustment. Lower voices produce a softer sound. For some voices the effective parameter range is narrower than the legal parameter range.

(3-2) CHANNEL MODE MESSAGES

STATUS

1011nnnn(BnH)

n = 0 - 15 VOICE CHANNEL NUMBER

CONTROL NUMBER

0ccccccc

c = CONTROL NUMBER

CONTROL VALUE

0vvvvvvv

v = DATA VALUE

(3-2-1) ALL SOUND OFF (Recive only)

(CONTROL NUMBER = 78H , DATA VALUE = 0)

Switches off all sound from the channel. Does not reset Note On and Hold On conditions established by Channel Messages.

(3-2-2) RESET ALL CONTROLLERS (Recive only)

(CONTROL NUMBER = 79H , DATA VALUE = 0)

Resets controllers as follows.

PITCH BEND CHANGE

0

(Center)

AFTER TOUCH

0

(min.)

MODULATION

0

(min.)

EXPRESSION

127 (max.)

SUSTAIN

0

(off)

SOSTENUTO

0

(off)

SOFT PEDAL

0

(off)

NRPN

Sets number to null. (Internal data remains unchanged)

RPN

Sets number to null. (Internal data remains unchanged)

PORTAMENT CONTROL

Resets portamento source note number

PORTAMENTO

0

(off)

(3-2-3) ALL NOTES OFF (Recive only)

(CONTROL NUMBER = 7BH , DATA VALUE = 0)

Switches off all of the channel’s “on” notes. However, any notes being held by SUSTAIN or SOSTENUTO continue to sound until SUSTAIN/SOSTENUTO goes off.

(3-2-4) OMNI OFF (Recive only) (CONTROL NUMBER = 7CH , DATA VALUE = 0)

Same processing as for All Notes Off.

(3-2-5) OMNI ON (Recive only) (CONTROL NUMBER = 7DH , DATA VALUE = 0)

Same processing as for All Notes Off. Omni On is not executed.

(3-2-6) MONO (Recive only) (CONTROL NUMBER = 7EH , DATA VALUE = 0)

Same processing as for All Notes Off. If the 3rd byte is in a range of 0-16 the corresponding channel will be changed to Mode 4 (m=1).

(3-2-7) POLY (Recive only) (CONTROL NUMBER = 7FH , DATA VALUE = 0)

Same processing as for All Sounds Off and the corresponding channel will be changed to Mode 3.

(3-3) REGISTERED PARAMETER NUMBER(RPN)

STATUS

1011nnnn(BnH)

n = 0 - 15 VOICE CHANNEL NUMBER

RPN LSB

01100100(64H)

 

RPN LSB NUMBER

0ppppppp

p = RPN LSB(refer to the list below)

RPN MSB

01100101(65H)

 

RPN MSB NUMBER 0qqqqqqq

q = RPN MSB(refer to the list below)

DATA ENTRY MSB

00000110(06H)

 

DATA VALUE

0mmmmmmm

m = Data Value

DATA ENTRY LSB

00100110(26H)

 

DATA VALUE

0lllllll

l = Data Value

First appoints the parameter for RPN MSB/LSB, then sets the parameter value for data entry MSB/LSB.

RPN

 

D.ENTRY

 

 

LSB MSB

MSB LSB

PARAMETER NAME

DATA RANGE

00H

00H

mmH —

PITCH BEND SENSITIVITY 00H - 18H (0 - 24 semitones)

01H

00H

mmH llH

FINE TUNE

{mmH,llH} = {00H,00H} - {40H,00H} - {7FH,7FH}

 

 

 

 

(-8192*100/8192) - 0 - (+8192*100/8192)

02H 00H

mmH —

COARSE TUNE

28H - 40H - 58H (-24 - 0 - +24 semitones)

7FH 7FH

— — NULL

 

Clears the current RPN number setting. Does not change the internal parameter settings.

(3-4) NON-REGISTERED PARAMETER NUMBER(NRPN) (Recive only)

STATUS

1011nnnn(BnH)

n = 0 - 15 VOICE CHANNEL NUMBER

NRPN LSB

01100010(62H)

 

NRPN LSB NUMBER

0ppppppp

p = NRPN LSB(refer to the list below)

NRPN MSB

01100011(63H)

 

NRPN MSB NUMBER

0qqqqqqq

q = NRPN MSB(refer to the list below)

DATA ENTRY MSB

00000110(06H)

 

DATA VALUE

0mmmmmmm

m = Data Value

First appoints the parameter for NRPN MSB/LSB, then sets the parameter value for data entry MSB/LSB.

NRPN

D.ENTRY

 

 

 

 

 

 

MSB LSB

MSB LSB

PARAMETER NAME

 

DATA RANGE

 

01H

08H

mmH —

VIBRATO RATE

00H

- 40H - 7FH (-64 - 0

- +63)

01H

09H

mmH —

VIBRATO DEPTH

00H

- 40H - 7FH (-64 - 0

- +63)

01H

0AH

mmH —

VIBRATO DELAY

00H

- 40H - 7FH (-64 - 0

- +63)

01H

20H

mmH —

FILTER CUTOFF FREQUENCY 00H - 40H - 7FH (-64 -

0 - +63)

01H

21H

mmH —

FILTER RESONANCE

00H

- 40H - 7FH (-64 - 0

- +63)

01H

63H

mmH —

EG ATTACK TIME

00H

- 40H - 7FH (-64 - 0

- +63)

01H

64H

mmH —

EG DECAY TIME

00H

- 40H - 7FH (-64 - 0

- +63)

01H

66H

mmH —

EG RELEASE

00H

- 40H - 7FH (-64 - 0

- +63)

14H

rrH

mmH —

DRUM FILTER CUTOFF FREQ. 00H

- 40H - 7FH (-64 -

0 - +63)

15H

rrH

mmH —

DRUM FILTER RESONANCE

 

00H

- 40H - 7FH (-64 -

0 - +63)

16H rrH

mmH —

DRUM AEG ATTACK RATE

00H

- 40H - 7FH (-64 - 0

- +63)

17H rrH

mmH —

DRUM AEG DECAY RATE

00H

- 40H - 7FH (-64 - 0

- +63)

18H rrH

mmH —

DRUM PITCH COARSE

00H

- 40H - 7FH (-64 - 0

- +63)

19H

rrH

mmH —

DRUM PITCH FINE

00H

- 40H - 7FH (-64 - 0

- +63)

1AH rrH

mmH —

DRUM LEVEL

00H

- 7FH (0 - max.)

 

1CH rrH

mmH —

DRUM PANPOT

00H

 

,01H - 40H - 7FH

 

 

 

 

 

 

(random,left - center - right)

1DH rrH

mmH —

DRUM REVERB SEND LEVEL

00H

- 7FH (0 - max.)

 

1EH rrH

mmH —

DRUM CHORUS SEND LEVEL

00H

- 7FH (0 - max.)

 

1FH rrH

mmH —

DRUM VARIATION SEND LEVEL

 

00H

- 7FH (0 - max.)

 

The MSG14H-1FH (for drums) message is accepted as long as the channel is set with a drum voice.

rrH : drum instrument note number

(3-5) SYSTEM REALTIME MESSAGES

(3-5-1) MIDI CLOCK

STATUS 11111000 (F8H)

Transmission: 96 clocks per measure are transmitted.

Reception: If the instrument’s clock is set to external, after FAH is received from the external device the instrument’s clock will sync with the 96 beats per measure received from the external device.

Decides whether the internal clock, or Timing Clocks received via the MIDI IN will be used.

(3-5-2) START

STATUS 11111010 (FAH)

Transmission: Transmitted when instrument’s Rhythm or Song playback is started.

Reception: Depending upon the condition, Rhythm, Song Playback, or Song Rec will start.

(3-5-3) STOP

STATUS 11111100 (FCH)

Transmission: Transmitted when instrument’s Rhythm or Song playback is stopped.

Reception: Depending upon the condition, Rhythm, Song Playback, or Song Rec will stop.

(3-5-4) ACTIVE SENSING

STATUS 11111110 (FEH)

Transmission: Transmitted approximately once every 200msec.

Reception: Sensing is started once this Code is received. If Status or Data is not received within 400ms, the MIDI Receive Buffer will be cleared, and all notes, including those being sustained, will be cut OFF. Also, all control values will be reset to their factory defaults.

CVP-98/96/600 11