Yamaha DM2000 Analog Input Spec, Analog Output Spec

Analog Input Spec 347
DM2000—Owner’s Manual
Analog Input Spec
In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.
For 2TR IN ANALOG 2 levels, 0 dBV is referenced to 1.00 Vrms.
All input AD converters (except INSERT IN 1–24) are 24-bit linear, 128-times oversampling.
+48 V DC (phantom power) is supplied to CH INPUT (1–24) XLR type connectors via individual switches.
Analog Output Spec
STEREO OUT [L, R], 0 dBV is referenced to 1.00 Vrms.
In these specifications, when dB represents a specific voltage, 0 dB is referenced to 0.775 Vrms.
All output DA converters (except INSERT OUT 1–24) are 24-bit, 128-times oversampling.
Input PAD GAIN Actual Load
Impedance
For Use With
Nominal
Input level
Connector
Sensitivity1
1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the unit
is set to maximum gain. (All faders and level controls are maximum position.)
Nominal Max.
before clip
INPUT A/B 1–24
0
–60 dB
3k Ω
50–600 Ω
Mics & 600 Ω
Lines
–70 dB
(0.245 mV)
–60 dB
(0.775 mV)
–46 dB
(3.88 mV)
A: XLR-3-31 type
(Balanced)2
2. XLR-3-31 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
–16 dB
–26 dB
(38.8 mV)
–16 dB
(0.123 V)
–2 dB
(616 mV)
B: Phone jack (TRS)
(Balanced)3
3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).
26 0dB
(775 mV)
+10 dB
(2.45 V)
+24 dB
(12.28 V)
INSERT IN 1–24 — 10K Ω600 Ω Lines –6dB
(388 mV)
+4 dB
(1.23 V)
+18 dB
(6.16 V)
Phone jack (TRS)
(Balanced)3
2TR IN ANALOG 1
[L, R] — 10K Ω600 Ω Lines +4 dB (1.23 V)
+4 dB
(1.23 V)
+18 dB
(6.16 V)
Phone jack (TRS)
(Balanced)3
2TR IN ANALOG 2
[L, R] — 10K Ω600 Ω Lines –10 dBV (0.316 V)
–10 dBV
(0.316 V)
+4 dBV
(1.58 V)
Phono
(Unbalanced)
Output Actual Source
Impedance
For Use
With
Nominal
GAIN SW1
1. The maximum output level of each OMNI OUT can be set internally.
Output level
Connector
Nominal Max.
before clip
STEREO OUT [L, R]
600 Ω10k Ω Lines — –10 dBV
(0.316 V)
+4 dBV
(1.58 V) Phono (Unbalanced)
150 Ω600 Ω Lines — +4 dB
(1.23 V)
+18 dB
(6.16 V) XLR-3-32 type (Balanced)2
2. XLR-3-32 type connectors are balanced (1=GND, 2=HOT, 3=COLD).
STUDIO MONITOR OUT
[L, R] 150 Ω10k Ω Lines — +4 dB (1.23 V)
+18 dB
(6.16 V)
Phone Jack (TRS)
(Balanced)3
3. Phone jacks are balanced (Tip=HOT, Ring=COLD, Sleeve=GND).
C-R MONITOR OUT LARGE
[L, R] 150 Ω600 Ω Lines — +4 dB (1.23 V)
+18 dB
(6.16 V) XLR-3-32 type (Balanced)2
C-R MONITOR OUT SMALL
[L, R] 150 Ω600 Ω Lines — +4 dB (1.23 V)
+18 dB
(6.16 V) XLR-3-32 type (Balanced)2
OMNI OUT 1–8 150 Ω10k Ω Lines
+18 dB
(default)
+4 dB
(1.23 V)
+18 dB
(6.16 V) Phone Jack (TRS)
(Balanced)3
+4 dB –10 dB
(0.245 V)
+4 dB
(1.23 V)
INSERT OUT 1–24 150 Ω10k Ω Lines — +4 dB
(1.23 V)
+18 dB
(6.16 V)
Phone Jack (TRS)
(Balanced)3
PHONES 100 Ω8 Ω Phones — 4 mW 25 mW Stereo Phone Jack (TRS)
(Unbalanced)4
4. PHONES stereo phone jack is unbalanced (Tip=LEFT, Ring=RIGHT, Sleeve=GND).
40 Ω Phones — 12 mW 75 mW