Troubleshooting
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
The sound suddenly | The protection circuitry has been activated | Check that the speaker wires are not touching each | — | |
goes off. | because of a short circuit, etc. | other and then turn this unit back on. |
| |
|
|
|
| |
| The sleep timer has turned off this unit. | Turn on this unit, and play the source again. | — | |
|
|
|
| |
| The sound is muted. | Press IMUTE or LVOLUME +/– to resume audio | 34 | |
|
| output. |
| |
|
|
|
| |
Sound is heard from | Incorrect cable connections. | Connect the cables properly. If the problem persists, | ||
the speaker on one |
| the cables may be defective. |
| |
side only. |
|
|
| |
Incorrect settings in “SP LEVEL”. | Adjust the “SP LEVEL” settings. | 40 | ||
| ||||
|
|
|
| |
Only the center | When playing a monaural source with a | This is not malfunction. | — | |
speaker outputs | CINEMA DSP program, the source signal |
|
| |
substantial sound. | is directed to the center channel, and the |
|
| |
| front and surround speakers output effect |
|
| |
| sounds. |
|
| |
|
|
|
| |
No sound is heard | “CENTER SP” in “SPEAKER SET” is set | Set “CENTER SP” to “SML” or “LRG”. | 50 | |
from the center | to “NONE”. |
|
| |
speaker. |
|
|
| |
Some sound field programs do not output | Try another sound field program. | 37 | ||
| ||||
| sounds from the center speaker. |
|
| |
|
|
|
| |
No sound is heard | “SUR. L/R SP” in “SPEAKER SET” is | Set “SUR. L/R SP” to “SML” or “LRG”. | 51 | |
from the surround | set to “NONE”. |
|
| |
speakers. |
|
|
| |
This unit is in the “STRAIGHT” mode | Press BSTRAIGHT so that “STRAIGHT” | 38 | ||
| ||||
| and a monaural source is being played | disappears from the front panel display. |
| |
| back. |
|
| |
|
|
|
| |
No sound from the | “FRONT B” in “SPEAKER SET” is set to | Set “FRONT B” to “FRONT”. | 50 | |
center, surround | “ZONE B”. |
|
| |
speakers when the |
|
|
| |
FRONT B speakers |
|
|
| |
are activated. |
|
|
| |
|
|
|
| |
No sound is heard | “LFE/BASS OUT” in “SPEAKER SET” | Set “LFE/BASS OUT” to “SWFR” or “BOTH”. | 51 | |
from the subwoofer. | is set to “FRNT” when a Dolby Digital or |
|
| |
| DTS signal is being played. |
|
| |
|
|
|
| |
| “LFE/BASS OUT” in “SPEAKER SET” | Set “LFE/BASS OUT” to “SWFR” or “BOTH”. | 51 | |
| is set to “SWFR” or “FRNT” when a 2- |
|
| |
| channel source is being played. |
|
| |
|
|
|
| |
| The source does not contain low- | This is not malfunction. | — | |
| frequency bass signals. |
|
| |
|
|
|
|
INFORMATION | ADDITIONAL |
|
|
English
