Yamaha HTR-5940 owner manual Speaker distance CSP Distance, Center graphic equalizer Dcenter GEQ

SET MENU

■Speaker distance C)SP DISTANCE

Use this feature to manually adjust the distance of each speaker and the delay applied to the respective channel. Ideally, each speaker should be the same distance from the main listening position. However, this is not possible in most home situations. Thus, a certain amount of delay must be applied to the sound from each speaker so that all sounds will arrive at the listening position at the same time.

Unit UNIT

Choices: meters (m), feet (ft) Initial setting:

[U.S.A. and Canada models]: feet (ft)

[Other models]: meters (m)

•Select “meters” to adjust speaker distances in meters.

•Select “feet” to adjust speaker distances in feet.

Speaker distances

Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)

Control step: 0.10 m (0.5 ft)

•Select “FRONT L” to adjust the distance of the front left speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “FRONT R” to adjust the distance of the front right speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “CENTER” to adjust the distance of the center speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “SUR. L” to adjust the distance of the surround left speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “SUR. R” to adjust the distance of the surround right speaker.

Initial setting: 3.00 m (10.0 ft)

•Select “SUR. B” to adjust the distance of the surround back speaker.

Initial setting: 2.10 m (7.0 ft)

•Select “SWFR” to adjust the distance of the subwoofer. Initial setting: 3.00 m (10.0 ft)

Note

“CENTER”, “SUR. L”, “SUR.R”, “SUR. B” and “SWFR” cannot be adjusted if “CENTER” (see page 78), “SUR. LR” (see page 78), “SUR. B” (see page 78) and “BASS OUT” (see page 79) are set to “NONE” respectively.

■Center graphic equalizer D)CENTER GEQ

Use this feature to adjust the built-in 5-frequency band (100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic equalizer for the center channel so that the tonal quality of the center speaker matches that of the front speakers. You can make adjustments while listening to the currently selected source component or a test tone.

Control range: –6 to +6 dB

Control step: 0.5 dB

Initial setting: 0 dB

y

Press u / d to select a frequency band and j / i to adjust the selected frequency band.

Following is an example where “100 Hz” is selected as the frequency band.

DVR V-AUX DTV/CBL pDVD MD/CD-R TUNER CD XM

	VOLUME
SP
A	dB

100Hz---- 0 dB

Test tone TEST

Choices: OFF, ON

•Select “OFF” to stop test tones and output the currently selected source component.

•Select “ON” to output test tones from the front left and center speakers, and adjust the tonal quality of the center speaker.

■Low-frequency effect level E)LFE LEVEL

Use this feature to adjust the output level of the LFE (low- frequency effect) channel according to the capacity of your subwoofer or headphones. The LFE channel carries low-frequency special effects which are only added to certain scenes. This setting is effective only when this unit decodes Dolby Digital or DTS signals.

Control range: –20 to 0 dB

Control step: 1 dB

Speaker SP LFE

Adjusts the speaker LFE level.

Headphone HP LFE

Adjusts the headphone LFE level.

Note

Depending on the settings of “BASS OUT” (see page 79), some signals may not be output at the SUBWOOFER OUTPUT jack.

80