12 3 4 5 6 7 8 9 10 Automatic speaker setup

Error messages

If any error message is displayed during the measurement, resolve the problem and perform YPAO again.

 

 

 

 

 

 

 

Error message

Cause

Remedy

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A u t o S e t u p

ERROR

 

 

 

 

E-1:No Front SP

Front speakers are not detected.

 

 

S t a r t

E-5:Noisy

 

 

 

Error

(E-1:NO FRNT SP)

Exit YPAO, turn off the unit, and then check the speaker

 

 

 

 

 

 

E x i t

 

 

 

 

message

 

 

connections.

 

 

 

 

 

E-2:No Sur. SP

One of the surround speakers cannot be

 

 

 

 

 

 

 

 

 

PROCEED

 

 

 

 

(E-2:NO SUR SP)

detected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5 %

 

 

 

E-4:SBR → SBL

A surround back speaker is connected to

When using only one surround back speaker, you need to

 

 

 

 

 

 

 

connect it to the SINGLE jack (L side). Exit YPAO, turn off the

 

 

 

 

 

 

 

(E-4:SBR -> SBL)

the R side only.

 

 

 

 

 

 

 

unit, and then reconnect the speaker.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TV screen

 

 

 

 

 

E-5:Noisy

 

Keep the room quiet and retry YPAO. If you select

 

 

 

 

 

 

The noise is too loud.

“PROCEED”, YPAO takes the measurement again and

 

 

 

 

 

 

 

(E-5:NOISY)

 

 

 

 

 

 

 

 

ignores any noise detected.

 

 

 

 

 

 

 

 

 

E-5:NOISY

Front display

VOL.

SW

C

L R

SLSR

E-6:Check Sur.

Surround back speakers are connected,

Surround speakers need to be connected in order to use

surround back speakers. Exit YPAO, turn off the unit, and

(E-6:CHECK SUR)

but no surround speakers are connected.

then reconnect the speakers.

 

 

 

 

 

E-7:No MIC

The YPAO microphone has been removed.

Connect the YPAO microphone to the YPAO MIC jack firmly

(E-7:NO MIC)

and retry YPAO.

 

■Procedure to handle errors

1Check the content of error message and press ENTER.

E-8:No Signal

The YPAO microphone cannot detect test

Connect the YPAO microphone to the YPAO MIC jack firmly

and retry YPAO. If this error occurs repeatedly, contact the

(E-8:NO SIGNAL)

tones.

nearest authorized Yamaha dealer or service center.

 

 

 

 

 

E-9:User Cancel

The measurement has been canceled.

Retry or exit YPAO as necessary.

(E-9:CANCEL)

 

 

2Use the cursor keys (e/r) to select the desired operation.

To exit the YPAO measurement:

a Select “EXIT” and press ENTER.

bUse the cursor keys (q/w) to select “Exit” and press

ENTER.

cDisconnect the YPAO microphone from the unit.

E-10:Internal Err.

 

Exit YPAO, and turn off and on the unit. If this error occurs

An internal error has occurred.

repeatedly, contact the nearest authorized Yamaha dealer or

(E-10:INTERNAL)

 

service center.

 

 

 

 

 

• Texts in parentheses denote indicators on the front display.

To retry the YPAO measurement from beginning:

Select “RETRY” and press ENTER.

To proceed with the current YPAO measurement (for E-5 and E-9 only):

Select “PROCEED” and press ENTER.

PREPARATIONS ➤ Optimizing the speaker settings automatically (YPAO)

En 33