TROUBLESHOOTING
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
|
|
|
| |
Distorted or too little bass sound. | CROSS OVER in SUBWOOFER SET is | Set CROSS OVER correctly. | 67 | |
| set incorrectly. |
| ||
|
|
| ||
|
|
|
| |
| One of the night listening modes is | Turn off the night listening modes. | 55 | |
| currently selected. |
| ||
|
|
| ||
|
|
|
| |
Too much bass sound. | TruBass is currently turned on. | Turn off TruBass. | 57 | |
|
|
|
| |
| The volume level of the subwoofer is too | Turn down the volume level of the | — | |
| high. | subwoofer. | ||
|
| |||
|
|
|
| |
Surround sound effects are | The listening room is not a regular shape. | Install this unit in a square or rectangular | — | |
insubstantial. |
| shaped room. |
| |
|
|
|
| |
| There is no wall in the path of the sound | Try placing a flat object, such as a board, | — | |
| beam. | in the path of the sound beam. |
| |
|
|
|
| |
Dolby Digital or DTS sources | The connected component is not set to | Make an appropriate setting following | — | |
cannot be played. (Dolby Digital or | output Dolby Digital or DTS digital | the operating instructions for your |
| |
DTS indicator does not light up in | signals. | component. |
| |
the front panel display.) |
|
|
| |
The input mode is set to ANALOG. | Set the input mode to AUTO. | 75 | ||
| ||||
|
|
|
| |
There is noise interference when a | The protection circuitry was in operation | Turn down the volume level. | 41 | |
subwoofer is not connected to this | because a source with strong bass |
|
| |
Select SWFR for BASS OUT. | 67 | |||
unit. | elements was played back. | |||
|
|
|
| |
|
| Connect a subwoofer and adjust settings | 67 | |
|
| for SUBWOOFER SET. |
| |
|
|
|
| |
Low frequency sounds are | CROSS OVER in SUBWOOFER SET is | Set CROSS OVER correctly. | 67 | |
distorted. | set incorrectly. |
|
| |
|
|
|
| |
The VIDEO OUT (composite) jack of | Connect the VIDEO OUT (composite) | 16 | ||
appear. | this unit is not connected to the video | jack of this unit to the video input jacks |
| |
| input jacks of your TV. | of your TV. The OSD is not output at the |
| |
|
| COMPONENT VIDEO OUT jacks. |
| |
|
|
|
| |
| The video pin cable is not connected | Connect the cable properly. | 16 | |
| properly. |
|
| |
|
|
|
| |
No picture is displayed for | The video pin cable is not connected | Connect the cable properly. | 17 | |
external components, such as a | properly. |
|
| |
DVD player. |
|
|
| |
|
|
|
| |
This unit does not operate | The internal microcomputer has been | Disconnect the AC power supply cable | — | |
properly. | frozen by an external electric shock | from the outlet and then plug it in again |
| |
| (such as lightning or excessive static | after about 30 seconds. |
| |
| electricity) or by a power supply with |
|
| |
| low voltage. |
|
| |
|
|
|
| |
There is noise interference from | This unit is too close to the digital or | Move this unit further away from such | — | |
digital or | equipment. |
| ||
equipment. |
|
|
| |
|
|
|
| |
This unit does not output effect | The original source includes surround | Disable surround effect settings on this | — | |
sounds properly. | effects. | unit. |
| |
|
|
|
| |
My beam | The listening room is too noisy. | Keep the listening room as quiet as | — | |
does not work. |
| possible. |
| |
|
|
|
| |
|
| Try manual adjustment. | 49 | |
|
|
|
| |
| The sound reflectivity of the listening | Set REFLECTING to HI ECHO. | 67 | |
| room is too much. |
|
| |
|
|
|
| |
| The remote control may be operated | The remote control will function within a | 24 | |
| outside of the remote control operation | maximum range of 6 m and no more than |
| |
| range. | 30 degrees |
| |
|
|
|
|
INFORMATION | ADDITIONAL |
|
|
|
|
English |
|
|
|
