|
| Troubleshooting | ||
|
|
|
| |
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
|
|
|
| |
No sound from the | BASS OUT in SUBWOOFER SET is set to | Select SUBWOOFER. | 80 | |
subwoofer. | FRONT. |
|
| |
|
|
|
| |
| The source does not contain low bass signals. |
|
| |
|
|
|
| |
Distorted or too little bass | CROSS OVER in SUBWOOFER SET is set | Set CROSS OVER correctly. | 80 | |
sound. | incorrectly. |
| ||
|
| |||
|
|
|
| |
| One of the night listening enhancers is | Turn off the night listening enhancers. | 69 | |
| currently selected. |
| ||
|
|
| ||
|
|
|
| |
Too much bass sound. | TruBass is currently turned on. | Turn off TruBass. | 81 | |
|
|
|
| |
| The volume level of the subwoofer is too high. | Turn down the volume level of the subwoofer. | — | |
|
|
|
| |
Surround sound effects are | The listening room is not a regular shape. | Install this unit in a square or rectangular | — | |
insubstantial. |
| shaped room. |
| |
|
|
|
| |
| There is no wall in the path of the sound | Try placing a flat object, such as a board, in | — | |
| beam. | the path of the sound beam. |
| |
|
|
|
| |
Dolby Digital or DTS sources | The connected component is not set to | Make an appropriate setting following the | — | |
cannot be played back. | output Dolby Digital or DTS digital signals. | operating instructions for your component. |
| |
(Dolby Digital or DTS |
|
|
| |
The input mode is set to ANALOG. | Set the input mode to AUTO. | 90 | ||
indicator does not light up in | ||||
the front panel display.) |
|
|
| |
|
|
|
| |
There is noise interference | The protection circuitry was in operation | Turn down the volume level. | 41 | |
when a subwoofer is not | because a source with strong bass elements |
|
| |
Select SUBWOOFER for BASS OUT. | 80 | |||
connected to this unit. | was played back. | |||
|
|
|
| |
|
| Connect a subwoofer and adjust settings for | 80 | |
|
| SUBWOOFER SET. |
| |
|
|
|
| |
| CROSS OVER in SUBWOOFER SET is set | Set CROSS OVER correctly. | 80 | |
distorted. | incorrectly. |
|
| |
|
|
|
| |
| The OSD video pin cable is not connected | Connect the cable properly. | 18 | |
appear. | properly. |
|
| |
|
|
|
| |
This unit does not operate | The internal microcomputer has been frozen | Disconnect the AC power supply cable from | — | |
properly. | by an external electric shock (such as | the outlet and plug it in again after about 30 |
| |
| lightning or excessive static electricity) or | seconds. |
| |
| by a power supply with low voltage. |
|
| |
|
|
|
| |
No sound is heard from the | The TV does not accept the | Convert the | — | |
TV connected via HDMI. | audio signals. | the |
| |
|
| component such as a DVD player. |
| |
|
|
|
| |
| “SUPPORT AUDIO” is set to | Set “SUPPORT AUDIO” to “OTHER”. | 84 | |
|
|
|
| |
There is noise interference | This unit is too close to the digital or high- | Move this unit farther away from such | — | |
from digital or high- | frequency equipment. | equipment. |
| |
frequency equipment. |
|
|
| |
|
|
|
| |
This unit does not output | The original source includes surround effects. | Disable the surround effect settings of this unit. | — | |
effect sounds properly. |
|
|
| |
|
|
|
| |
My Beam | The listening room is too noisy. | Keep the listening room as quiet as possible. | — | |
function does not work. |
|
|
| |
| Try | 64 | ||
|
| |||
|
|
|
| |
| The sound reflectivity of the listening room | Set REFLECTING to HI ECHO. | 81 | |
| is too much. |
|
| |
|
|
|
| |
| The remote control may be operated outside | The remote control functions within a | 24 | |
| of the remote control operation range. | maximum range of 6 m (20 ft) and no more |
| |
|
| than 45 degrees |
| |
|
| panel. |
| |
|
|
|
| |
| The function does not work properly | Select My Beam and then try again. | 63 | |
| because of the condition of the connected |
|
| |
| components. |
|
| |
|
|
|
| |
INFORMATION | ADDITIONAL |
|
|
|
|
English |
|
|
|
