Color profile: Disabled

Composite Default screen

 

 

￿￿￿￿￿ $￿ ￿￿"￿￿%￿￿ ￿￿￿& ￿￿￿￿ ￿￿'￿￿￿￿￿ +,￿￿￿￿￿￿￿￿-

 

￿￿￿￿￿ ￿￿￿￿￿ *￿￿)￿￿￿

*￿￿￿￿￿)￿￿￿￿

B

 

$$￿85￿ +$￿+

$$￿85￿ ￿￿￿￿￿￿￿￿￿￿￿￿￿ ￿￿￿￿ ￿￿￿￿￿￿￿￿￿￿

 

 

 

 

1

 

￿$￿58C /98,

￿￿￿￿￿￿ /￿￿￿ ￿￿￿￿￿￿￿￿￿￿￿￿￿ ￿￿￿￿ ￿￿￿￿￿￿￿￿￿￿ ￿365+ ￿6￿+9￿￿$,4

 

+$￿+

&￿￿￿ ￿￿ ￿￿￿￿￿ ￿￿ ￿￿￿ ￿￿￿￿￿￿￿ ￿￿ ￿￿ ￿￿￿￿ ￿￿ ￿￿￿￿￿￿￿￿!

 

 

 

 

 

 

 

 

 

,￿￿￿￿￿￿￿￿ ￿￿ ￿￿& ￿￿￿ ￿￿￿￿￿ ￿￿￿￿￿￿ &￿￿ ￿￿￿ ￿￿￿ ￿￿￿ ￿￿￿￿￿￿￿ &￿￿￿

 

 

 

￿￿￿￿ ￿￿ ￿￿￿ ￿￿￿￿￿ &￿￿ ￿￿ ￿￿￿￿￿ ￿￿￿￿￿￿￿ ￿￿￿￿￿￿￿￿￿ ￿￿￿￿￿￿ ￿￿￿ ￿￿￿￿￿

:D

 

 

￿￿￿￿￿￿￿￿ ￿￿￿ ￿￿￿￿￿ ￿￿￿￿￿￿ ￿￿￿ ￿￿￿￿ ￿￿￿ ￿￿ ￿￿￿￿ ￿￿￿￿￿￿￿ ￿￿ ￿￿

 

 

 

￿￿￿￿￿ ￿￿￿ ￿￿ ￿￿￿￿ +￿￿ ￿￿￿ ￿￿ ￿￿￿￿￿￿￿ ￿￿￿￿ ￿￿￿￿￿￿￿￿ ￿￿￿￿ ￿￿

 

 

 

￿"￿

 

 

 

 

::

 

￿8￿6+$8 8$9,C

￿￿￿￿￿￿￿ ￿￿ ￿￿￿￿￿ ￿￿￿ ￿￿￿￿￿￿￿￿￿￿

 

 

 

 

Configuration and Calibration

After you have installed the media and ribbon and the POST (Power-On Self Test) is complete, the front panel display will show “PRINTER READY.” You may now set printer parameters for your application using the front panel display and the five keys directly below it.

If it becomes necessary to restore the initial printer defaults, see “Feed Key and Pause Key Self Test” on page 68.

NOTE: Unless otherwise noted, all parameters are listed in the order they are displayed, starting with “DARKNESS”.

Entering the Program Mode

To enter the programming mode, press the Setup/Exit key. Press either the Next/Save key or Previous key to scroll to the parameter you wish to set. Parameters in this section are shown in the order displayed when pressing the Next/Save key. Throughout this process, press the Next/Save key to continue to the next parameter; or, press the Previous key to go back to the previous parameter in the cycle.

An asterisk (*) in the upper left hand corner of the display indicates that the value displayed is different than the currently stored value.

Zebra XiII-Series User’s Guide

29

41

H:...Xi2UsersGuideR2.vp

Fri Aug 07 10:35:48 1998