Husqvarna 15T AWD, 15Ts AWD manual Presentation

Page 12

PRESENTATION

Presentation

Congratulations on your choice of an excellent quality product that will give you great pleasure for many years. This operator’s manual describes Rider 15T, Rider 15Ts AWD and Rider 15T AWD.

The machines are equipped with chronometer and lights.

Rider 15T AWD is equipped with all wheel drive. Rider 15Ts AWD is also equipped with power steering.

The power transmission from the engine is handled by a hydrostatic gearbox, which allows variable variation of the speed by using the pedals.

One pedal for driving forward and one for reverse.

Throttle control

The throttle control regulates the engine speed, and thereby also the rotation speed of the blades.

To increase or reduce the engine speed the control is moved forwards or backwards.

Avoid idling the engine for long periods, as there is a risk of carbon build-up on the spark plugs.

Choke control

The choke lever is used for cold starting and to give the engine a richer fuel mixture.

For cold starting the lever is moved backwards to its end position.

Speed limiter

The speed of the machine is steplessly regulated with two pedals. Pedal (1) is used to drive forwards, and pedal (2) to drive backwards.

!	WARNING! Make sure that branches do not
	obstruct the pedals when mowing under
	bushes. Otherwise there is a risk you may
	lose control.

Parking brake

The parking brake is applied as follows:

1Press down the parking brake pedal (1).

2Press in the lock button (2) on the steering column.

3Release the parking brake pedal while keeping the button pressed in.

The parking brake lock disengages automatically when the brake pedal is pressed.

12 – English

Image 12

Contents Rider 15T Rider 15T AWD Rider 15Ts AWD EnglishContents Service journal Pre-delivery serviceAfter the ﬁrst 8 hours Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? What is what on the ride-on mowerSafety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Cutting height adjustment lever Cutting unitLifting lever for the cutting unit LightsExercise care and refuel outdoors see safety instructions FuellingRelease lever Clutch control Rider 15T AWD and Rider 15Ts AWDDriving Before startingStart the engine Starting the engine with a weak battery Connecting the jump leadsDriving the Rider Remove the cables in the reverse orderCutting tips Stop the engineMaintenance Maintenance scheduleCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Adjusting the parking brake Rider 15T Checking and adjusting of throttle wireCan result in reduced braking ability Checking and adjusting the choke wire Replacement of fuel ﬁlterReplacing the air ﬁlter Cool before starting to replace the air ﬁlterChecking the fuel pump’s air ﬁlter Ignition systemReplacing the spark plug Check the safety system Replacing the light bulbs Main fuseChecking the tyre pressure Checking the engine’s cooling air intakeWhen the engine is running. Mind your ﬁngers Fitting the cutting headTrapping your hand Lift up the cutting unitRemoving the cutting unit Adjusting the parallelism of the cutting unit Hands when working with the bladesChecking the cutting unit’s parallelism Replacing the cutting unit beltsService position for the cutting unit Placing in the service positionRestoring from service position Checking the bladesRemoving the BioClip plug CombiClip 103, CombiClipLubrication Checking the engine’s oil levelChanging the oil ﬁlter Replacing the engine oilLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Troubleshooting schedule Problem ProcedureService StorageWinter storage GuardTechnical data Cutting unit CombiClip EC-declaration of conformity Applies to Europe only EC-declaration of conformityEN ISO 12100-2, EN-836 Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨