Husqvarna 15T AWD, 15Ts AWD manual Service journal, Pre-delivery service, After the ﬁrst 8 hours

Page 3

Service journal

Pre-delivery service

1 Charge the battery for 4 hours at max. 3 amp.

2 Fit steering wheel, seat and any optional equipment.

3Check and adjust tyre pressure (60 Kpa, 0.6 bar, 9 PSI).

4Adjust cutting unit:

Adjust lift springs (effective weight of cutting unit should be 12-15kg / 26.5-33 lb).

Adjust cutting unit so that rear edge is about 2-4 mm / 1/8” higher than front edge.

Adjust the cutting unit’s cutting height setting so that the connection rod is tensed at the lowest cutting height.

5 Check that the right amount of oil is in the engine.

6 Check that there is oil in the transmission’s oil tank.

7 Connect battery.

8 Fill with fuel and start engine.

9Check that machine does not move in neutral.

10Check:

Forward drive.

Reverse drive.

Operation of blades.

Seat safety switch.

Lif lever safety switch.

The safety switch for the hydrostat pedals.

11 Check the engine speed See the Technical data section.

12Check the synchronisation between the front and rear wheels. (Only AWD-machines) See the workshop manual.

13Tell customer about:

Needs and beneﬁts of following the service schedule.

Servicing and the inﬂuence of this journal on the second-hand value of the machine.

Range of applications for BioClip.

Complete proof of sale etc.

Pre-delivery service carried out. No outstanding problems. Certiﬁed:

___________________________________________________________________

Date, mileage, stamp, signature

After the ﬁrst 8 hours

1 Change engine oil

2 Change the oil in the gearbox. (Only AWD-machines)

3 Check the synchronisation between the front and rear wheels. (Only AWD-machines)

English – 3

Image 3

Contents English Rider 15T Rider 15T AWD Rider 15Ts AWDContents Service journal Pre-delivery serviceAfter the ﬁrst 8 hours Introduction Symbols KEY to SymbolsKEY to Symbols What is what on the ride-on mower What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lights Cutting height adjustment leverCutting unit Lifting lever for the cutting unitClutch control Rider 15T AWD and Rider 15Ts AWD Exercise care and refuel outdoors see safety instructionsFuelling Release leverDriving Before startingStart the engine Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Driving the RiderStop the engine Cutting tipsMaintenance schedule MaintenanceCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Adjusting the parking brake Rider 15T Checking and adjusting of throttle wireCan result in reduced braking ability Cool before starting to replace the air ﬁlter Checking and adjusting the choke wireReplacement of fuel ﬁlter Replacing the air ﬁlterChecking the fuel pump’s air ﬁlter Ignition systemReplacing the spark plug Check the safety system Checking the engine’s cooling air intake Replacing the light bulbsMain fuse Checking the tyre pressureLift up the cutting unit When the engine is running. Mind your ﬁngersFitting the cutting head Trapping your handRemoving the cutting unit Replacing the cutting unit belts Adjusting the parallelism of the cutting unitHands when working with the blades Checking the cutting unit’s parallelismPlacing in the service position Service position for the cutting unitCombiClip 103, CombiClip Restoring from service positionChecking the blades Removing the BioClip plugReplacing the engine oil LubricationChecking the engine’s oil level Changing the oil ﬁlterLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Problem Procedure Troubleshooting scheduleGuard ServiceStorage Winter storageTechnical data Cutting unit CombiClip EC-declaration of conformity Applies to Europe only EC-declaration of conformityEN ISO 12100-2, EN-836 Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨