Husqvarna 15Ts AWD, 15T AWD manual Contents

Page 2

CONTENTS

Contents
CONTENTS
Contents	2
Service journal
Pre-delivery service	3
After the ﬁrst 8 hours	3
INTRODUCTION
Dear Customer,	4
Driving and transport on public roads	4
Towing	4
Use	4
Good service	4
KEY TO SYMBOLS
Symbols	5
WHAT IS WHAT?
What is what on the ride-on mower	7
SAFETY INSTRUCTIONS
Safety instructions	8
Driving on slopes	9
Children	10
Maintenance	10
Transport	11
PRESENTATION
Presentation	12
Throttle control	12
Choke control	12
Speed limiter	12
Parking brake	12
Cutting unit	13
Lifting lever for the cutting unit	13
Cutting height adjustment lever	13
Lights	13
Counter	13
Seat	13
Fuelling	14
Release lever	14
Driving
Before starting	15
Start the engine	15
Starting the engine with a weak battery	16
Driving the Rider	16
Cutting tips	17
Stop the engine	17
Maintenance
Maintenance schedule	18
Cleaning	19
Removing of the machine hoods	19
Checking and adjusting the steering wires	19
Adjusting the parking brake Rider 15T	20
Adjusting the parking brake	20
Checking and adjusting of throttle wire	20
Checking and adjusting the choke wire	21
Replacement of fuel ﬁlter	21
Replacing the air ﬁlter	21
Checking the fuel pump’s air ﬁlter	22
Ignition system	22
2 – English

Check the safety system	23
Replacing the light bulbs	24
Main fuse	24
Checking the tyre pressure	24
Checking the engine’s cooling air intake	24
Fitting the cutting head	25
Removing the cutting unit	26
Checking and adjustment of the cutting unit’s ground
pressure	26
Checking the cutting unit’s parallelism	27
Adjusting the parallelism of the cutting unit	27
Replacing the cutting unit belts	27
Service position for the cutting unit	28
Checking the blades	29
Removing the BioClip plug	29
Lubrication
Checking the engine’s oil level	30
Changing the oil ﬁlter	30
Checking the transmission oil level	31
Lubricating the belt adjuster	31
General lubrication	31
Troubleshooting schedule
Storage
Winter storage	33
Guard	33
Service	33
Technical data
EC-declaration of conformity	36
EC-declaration of conformity	36

Image 2

Contents Rider 15T Rider 15T AWD Rider 15Ts AWD EnglishContents After the ﬁrst 8 hours Service journalPre-delivery service Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? What is what on the ride-on mowerInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Lifting lever for the cutting unit Cutting height adjustment leverCutting unit LightsRelease lever Exercise care and refuel outdoors see safety instructionsFuelling Clutch control Rider 15T AWD and Rider 15Ts AWDStart the engine DrivingBefore starting Driving the Rider Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse orderCutting tips Stop the engineMaintenance Maintenance scheduleRemoving of the machine hoods CleaningChecking and adjusting the steering wires Can result in reduced braking ability Adjusting the parking brake Rider 15TChecking and adjusting of throttle wire Replacing the air ﬁlter Checking and adjusting the choke wireReplacement of fuel ﬁlter Cool before starting to replace the air ﬁlterReplacing the spark plug Checking the fuel pump’s air ﬁlterIgnition system Check the safety system Checking the tyre pressure Replacing the light bulbsMain fuse Checking the engine’s cooling air intakeTrapping your hand When the engine is running. Mind your ﬁngersFitting the cutting head Lift up the cutting unitRemoving the cutting unit Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitHands when working with the blades Replacing the cutting unit beltsService position for the cutting unit Placing in the service positionRemoving the BioClip plug Restoring from service positionChecking the blades CombiClip 103, CombiClipChanging the oil ﬁlter LubricationChecking the engine’s oil level Replacing the engine oilGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Troubleshooting schedule Problem ProcedureWinter storage ServiceStorage GuardTechnical data Cutting unit CombiClip EN ISO 12100-2, EN-836 EC-declaration of conformity Applies to Europe onlyEC-declaration of conformity Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨