Husqvarna 15T AWD, 15Ts AWD manual Cleaning, Removing of the machine hoods

Page 19

Maintenance

Cleaning

Clean the machine directly after use. It is much easier to wash off grass cuttings before they dry.

Oily dirt can be removed using a cold degreasing agent. Spray on a thin layer.

Rinse at normal water pressure.

Do not direct the jet towards electrical components or bearings.

Do not rinse hot surfaces such as the engine and exhaust system.

It is recommended that you start the engine and run the mower for a short period after cleaning, so that any remaining water is blown off.

Lubricate the machine if necessary after cleaning. Carry out extra lubrication when the bearings have been exposed to a degreaser or a water jet.

IMPORTANT INFORMATION

Avoid using a high pressure washer or a steam cleaner. There is a major risk of water penetrating into bearings and electrical connections. Corrosion attack can result, which will lead to running problems. Cleaning additives generally aggravate the damage.

Removing of the machine hoods

Engine cover

The engine becomes accessible for service when the engine cover is opened.

Fold the seat forward, loosen the snap lock under the seat and fold the cover backwards.

Front cover

Release the clip on the front hood and lift off the fender.

Right-hand fender

Remove the accelerator knob (1), screws (2 and 3), and remove the cover.

Left-hand fender

Remove the screws holding the wing cover (2) and lift off the cover.

Checking and adjusting the steering wires

The steering is controlled by means of wires.

These can in time become slack, which implies that the adjustment of the steering becomes altered.

Check and adjust the steering as follows:

1Remove the frame plate by loosening the screws (2) and lift the frame plate by the rear edge.

English – 19

Image 19

Contents English Rider 15T Rider 15T AWD Rider 15Ts AWDContents Pre-delivery service Service journalAfter the ﬁrst 8 hours Introduction Symbols KEY to SymbolsKEY to Symbols What is what on the ride-on mower What is WHAT?General use Safety InstructionsSafety instructions Insure your RiderThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Lights Cutting height adjustment leverCutting unit Lifting lever for the cutting unitClutch control Rider 15T AWD and Rider 15Ts AWD Exercise care and refuel outdoors see safety instructionsFuelling Release leverBefore starting DrivingStart the engine Remove the cables in the reverse order Starting the engine with a weak batteryConnecting the jump leads Driving the RiderStop the engine Cutting tipsMaintenance schedule MaintenanceChecking and adjusting the steering wires CleaningRemoving of the machine hoods Checking and adjusting of throttle wire Adjusting the parking brake Rider 15TCan result in reduced braking ability Cool before starting to replace the air ﬁlter Checking and adjusting the choke wireReplacement of fuel ﬁlter Replacing the air ﬁlterIgnition system Checking the fuel pump’s air ﬁlterReplacing the spark plug Check the safety system Checking the engine’s cooling air intake Replacing the light bulbsMain fuse Checking the tyre pressureLift up the cutting unit When the engine is running. Mind your ﬁngersFitting the cutting head Trapping your handRemoving the cutting unit Replacing the cutting unit belts Adjusting the parallelism of the cutting unitHands when working with the blades Checking the cutting unit’s parallelismPlacing in the service position Service position for the cutting unitCombiClip 103, CombiClip Restoring from service positionChecking the blades Removing the BioClip plugReplacing the engine oil LubricationChecking the engine’s oil level Changing the oil ﬁlterChecking the transmission oil level Lubricating the belt adjusterGeneral lubrication Problem Procedure Troubleshooting scheduleGuard ServiceStorage Winter storageTechnical data Cutting unit CombiClip EC-declaration of conformity EC-declaration of conformity Applies to Europe onlyEN ISO 12100-2, EN-836 Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨