Husqvarna 15Ts AWD Adjusting the parking brake Rider 15T, Checking and adjusting of throttle wire

Page 20

Maintenance

2Check the tension of the steering wires by squeezing them together by the arrows as illustrated. It should be possible to push them together so that the distance between them is half as much, without using unnecessary force.

3If necessary, the wires can be adjusted by tightening the adjuster nuts on each side of the steering collar. Do not over tighten the cables; they should only be drawn in towards the steering collar.

Hold the cable, for example using an adjustable wrench, so that it does not twist.

If the adjustment is only made on one side, the middle position of the steering will be affected.

Check the wire tension on completion of the adjustment as per item 2.

Adjusting the parking brake Rider 15T

The parking brake is adjusted as follows:

1Loosen the locking nuts (1).

2Tension the cable using the adjuster screw (2) until the play in the cable is taken up.

3Tighten the locking nuts (1) after adjustment.

4The parking brake should be checked again after the adjustment has been made.

WARNING! A poorly adjusted parking brake

!can result in reduced braking ability.

Adjusting the parking brake Rider 15T AWD and Rider 15Ts AWD

Check that the parking brake is adjusted correctly by placing the machine on a slope with the front and rear axles disengaged.

Apply and lock the parking brake. When the machine does not stand still, the parking brake should be adjusted according to the following.

1 Remove the left-hand wing cover.

2 Loosen the locking nuts (1).

3Tension the cable using the adjuster screw (2) until the play in the cable is taken up.

4Tighten the locking nuts (1).

5The brake should be checked again after adjustment

6Assemble the left-hand wing cover.

Checking and adjusting of throttle wire

Check that the engine responds to the throttle control and that the correct engine speed is achieved at full throttle.

If doubts arise, contact your service representative.

If adjustment is necessary, adjust the lower wire as follows:

1Loosen the clamping screw for the cable’s outer casing and move the throttle to the full throttle position.

2Check that the throttle wire is attached to the correct hole in the lower lever, see diagram.

3Pull the throttle wire casing to the far left and tighten the clamping screw.

20 – English

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Rider 15T Rider 15T AWD Rider 15Ts AWD EnglishContents After the first 8 hours Service journalPre-delivery service Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? What is what on the ride-on mowerSafety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Cutting height adjustment lever Cutting unitLifting lever for the cutting unit LightsExercise care and refuel outdoors see safety instructions FuellingRelease lever Clutch control Rider 15T AWD and Rider 15Ts AWDStart the engine DrivingBefore starting Starting the engine with a weak battery Connecting the jump leadsDriving the Rider Remove the cables in the reverse orderCutting tips Stop the engineMaintenance Maintenance scheduleRemoving of the machine hoods CleaningChecking and adjusting the steering wires Can result in reduced braking ability Adjusting the parking brake Rider 15TChecking and adjusting of throttle wire Checking and adjusting the choke wire Replacement of fuel filterReplacing the air filter Cool before starting to replace the air filterReplacing the spark plug Checking the fuel pump’s air filterIgnition system Check the safety system Replacing the light bulbs Main fuseChecking the tyre pressure Checking the engine’s cooling air intakeWhen the engine is running. Mind your fingers Fitting the cutting headTrapping your hand Lift up the cutting unitRemoving the cutting unit Adjusting the parallelism of the cutting unit Hands when working with the bladesChecking the cutting unit’s parallelism Replacing the cutting unit beltsService position for the cutting unit Placing in the service positionRestoring from service position Checking the bladesRemoving the BioClip plug CombiClip 103, CombiClipLubrication Checking the engine’s oil levelChanging the oil filter Replacing the engine oilGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Troubleshooting schedule Problem ProcedureService StorageWinter storage GuardTechnical data Cutting unit CombiClip EN ISO 12100-2, EN-836 EC-declaration of conformity Applies to Europe onlyEC-declaration of conformity Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨
Top Page Image Contents