Husqvarna 15Ts AWD, 15T AWD manual Troubleshooting schedule, Problem Procedure

Page 32


Troubleshooting schedule
Problem	Procedure
Engine does not start	There is no fuel in the fuel tank
	Spark plug defective
	Faulty spark plug connections or interchanged cables
	Dirt in the carburettor or fuel line
	Starter motor does not turn over the engine
Starter motor does not turn over the engine	Battery ﬂat
	Bad contact between the cable and battery
	Lift lever for cutting unit in wrong position
	Main fuse blown.
	This fuse is in front of the battery, under the battery cover.
	Ignition lock faulty
	Brake not activated.
	Faulty starter motor
Engine does not run smoothly	Faulty spark plug.
	Carburettor incorrectly set
	Air ﬁlter clogged
	Fuel tank vent blocked
	Ignition key defective
	Dirt in the carburettor or fuel line
	Choking or incorrectly adjusted throttle cable
Engine seems to have no power	Air ﬁlter clogged
	Faulty spark plug.
	Dirt in the carburettor or fuel line
	Carburettor incorrectly set
	Choking or incorrectly adjusted throttle cable
Engine overheats	Engine overloaded
	Air intake or cooling ﬂanges blocked
	Fan damaged
	Too little or no oil in engine
	Ignition defective
	Faulty spark plug.
Battery does not charge	One or more battery cells faulty
	Poor contact on the battery terminal cable connectors
Machine vibrates	Blades are loose
	Engine is loose
	One or more blades unbalanced, caused by damage or poor balancing after sharpening
Uneven mowing	Blades blunt
	Cutting unit skew
	Long or wet grass
	Grass blockage under hood
	Different tyre pressures on right and left sides

Over-speeding

Engine speed too low

Drive belt slipping

32 – English

Image 32

Contents Rider 15T Rider 15T AWD Rider 15Ts AWD EnglishContents After the ﬁrst 8 hours Service journalPre-delivery service Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? What is what on the ride-on mowerSafety Instructions Safety instructionsInsure your Rider General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Cutting height adjustment lever Cutting unitLifting lever for the cutting unit LightsExercise care and refuel outdoors see safety instructions FuellingRelease lever Clutch control Rider 15T AWD and Rider 15Ts AWDStart the engine DrivingBefore starting Starting the engine with a weak battery Connecting the jump leadsDriving the Rider Remove the cables in the reverse orderCutting tips Stop the engineMaintenance Maintenance scheduleRemoving of the machine hoods CleaningChecking and adjusting the steering wires Can result in reduced braking ability Adjusting the parking brake Rider 15TChecking and adjusting of throttle wire Checking and adjusting the choke wire Replacement of fuel ﬁlterReplacing the air ﬁlter Cool before starting to replace the air ﬁlterReplacing the spark plug Checking the fuel pump’s air ﬁlterIgnition system Check the safety system Replacing the light bulbs Main fuseChecking the tyre pressure Checking the engine’s cooling air intakeWhen the engine is running. Mind your ﬁngers Fitting the cutting headTrapping your hand Lift up the cutting unitRemoving the cutting unit Adjusting the parallelism of the cutting unit Hands when working with the bladesChecking the cutting unit’s parallelism Replacing the cutting unit beltsService position for the cutting unit Placing in the service positionRestoring from service position Checking the bladesRemoving the BioClip plug CombiClip 103, CombiClipLubrication Checking the engine’s oil levelChanging the oil ﬁlter Replacing the engine oilGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Troubleshooting schedule Problem ProcedureService StorageWinter storage GuardTechnical data Cutting unit CombiClip EN ISO 12100-2, EN-836 EC-declaration of conformity Applies to Europe onlyEC-declaration of conformity Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨