Husqvarna 15Ts AWD, 15T AWD manual Removing the cutting unit

Page 26

Maintenance

9 Hook up the height adjustment strut.

10 Secure the collet spring.

11 Fit the front cover.

Removing the cutting unit

WARNING! Wear protective glasses when

!dismantling the cutting unit. The spring which tensions up the belt may break and cause personal injury.

1Carry out points 1-6 to put the cutting unit in the service position, see Service position for the cutting unit.

2Lower the cutting unit.

3 Open the unit catch.

4 Pull out the cutting unit.

	!	WARNING! Observe caution to avoid
	!	trapping your hand.
		trapping your hand.

Checking and adjustment of the cutting unit’s ground pressure

To achieve the best cutting results the cutting unit should follow the underlying surface without pressing too hard against it.

Pressure is adjusted using a screw and spring on each side of the Rider.

1Check the air pressure in the tyres 60 kPa/0.6 kp/cm2/8.5 PSI.

2Place the machine on a ﬂat surface.

3Put the lifting lever in the mowing position.

4Place a set of bathroom scales under the cutting unit’s frame (front edge) so that it rests on the scales. If necessary a block can be placed between the frame and scales so that the support wheels do not bear any weight.

5Adjust the unit’s ground pressure by screwing in or out the adjusting screws located behind the front wheels on both sides. The ground pressure should be between 12 and 15 kg (26.5-33 lb).

26 – English

Image 26

Contents Rider 15T Rider 15T AWD Rider 15Ts AWD EnglishContents After the ﬁrst 8 hours Service journalPre-delivery service Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? What is what on the ride-on mowerInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Lifting lever for the cutting unit Cutting height adjustment leverCutting unit LightsRelease lever Exercise care and refuel outdoors see safety instructionsFuelling Clutch control Rider 15T AWD and Rider 15Ts AWDStart the engine DrivingBefore starting Driving the Rider Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse orderCutting tips Stop the engineMaintenance Maintenance scheduleRemoving of the machine hoods CleaningChecking and adjusting the steering wires Can result in reduced braking ability Adjusting the parking brake Rider 15TChecking and adjusting of throttle wire Replacing the air ﬁlter Checking and adjusting the choke wireReplacement of fuel ﬁlter Cool before starting to replace the air ﬁlterReplacing the spark plug Checking the fuel pump’s air ﬁlterIgnition system Check the safety system Checking the tyre pressure Replacing the light bulbsMain fuse Checking the engine’s cooling air intakeTrapping your hand When the engine is running. Mind your ﬁngersFitting the cutting head Lift up the cutting unitRemoving the cutting unit Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitHands when working with the blades Replacing the cutting unit beltsService position for the cutting unit Placing in the service positionRemoving the BioClip plug Restoring from service positionChecking the blades CombiClip 103, CombiClipChanging the oil ﬁlter LubricationChecking the engine’s oil level Replacing the engine oilGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Troubleshooting schedule Problem ProcedureWinter storage ServiceStorage GuardTechnical data Cutting unit CombiClip EN ISO 12100-2, EN-836 EC-declaration of conformity Applies to Europe onlyEC-declaration of conformity Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨