Husqvarna 15T AWD, 15Ts AWD Checking and adjusting the choke wire, Replacement of fuel filter

Page 21

Maintenance

Checking and adjusting the choke wire

If the engine is producing black smoke or is difficult to start then the choke wire (upper wire) may be incorrectly adjusted.

If doubts arise, contact your service representative.

If it is necessary to adjust the choke, proceed as follows:

1Release the clamping screw that secures the wire casing and set the choke control to maximum choke.

2Check that the throttle wire is attached to the upper lever, see diagram.

3Pull the choke wire casing to the far right and tighten the clamping screw.

Replacement of fuel filter

Replace the fuel filter every 100 running hours (once per season) or more frequently if it is clogged.

Replace the filter as follows:

1Open the engine cover.

2Move the hose clips away from the filter. Use a pair of flat pliers.

3Pull off the filter from the hose ends.

4Press the new filter into the ends of the hoses. If necessary apply liquid detergent to the ends of the filter to facilitate connection.

5Push the hose clips back on the filter and tighten.

Replacing the air filter

!

WARNING! The exhaust system is hot. Let it

cool before starting to replace the air filter.

 

If the engine seems to lack power or does not run smoothly this may be because the air filter is clogged. It is therefore important to replace the air filter at regular intervals (see Maintenance/Maintenance Schedule for the correct service interval).

Replace the air filter as follows:

1Remove the air filter unit by pressing on the catches with your fingers.

IMPORTANT INFORMATION

Never run the engine without the air filter fitted.

The filters must not be oiled. They must be fitted dry.

2Remove the pre-filter and paper filter from the air filter unit.

3 Clean the pre-filter by washing it with water and detergent.

4Dry the pre-filter properly.

5Tap the paper filter against a hard surface to shake off the dust.

English – 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents English Rider 15T Rider 15T AWD Rider 15Ts AWDContents Service journal Pre-delivery serviceAfter the first 8 hours Introduction Symbols KEY to SymbolsKEY to Symbols What is what on the ride-on mower What is WHAT?Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Cutting unit Cutting height adjustment leverLifting lever for the cutting unit LightsFuelling Exercise care and refuel outdoors see safety instructionsRelease lever Clutch control Rider 15T AWD and Rider 15Ts AWDDriving Before startingStart the engine Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse orderStop the engine Cutting tipsMaintenance schedule MaintenanceCleaning Checking and adjusting the steering wiresRemoving of the machine hoods Adjusting the parking brake Rider 15T Checking and adjusting of throttle wireCan result in reduced braking ability Replacement of fuel filter Checking and adjusting the choke wireReplacing the air filter Cool before starting to replace the air filterChecking the fuel pump’s air filter Ignition systemReplacing the spark plug Check the safety system Main fuse Replacing the light bulbsChecking the tyre pressure Checking the engine’s cooling air intakeFitting the cutting head When the engine is running. Mind your fingersTrapping your hand Lift up the cutting unitRemoving the cutting unit Hands when working with the blades Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit beltsPlacing in the service position Service position for the cutting unitChecking the blades Restoring from service positionRemoving the BioClip plug CombiClip 103, CombiClipChecking the engine’s oil level LubricationChanging the oil filter Replacing the engine oilLubricating the belt adjuster Checking the transmission oil levelGeneral lubrication Problem Procedure Troubleshooting scheduleStorage ServiceWinter storage GuardTechnical data Cutting unit CombiClip EC-declaration of conformity Applies to Europe only EC-declaration of conformityEN ISO 12100-2, EN-836 Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨
Top Page Image Contents