Husqvarna 15T AWD manual Cutting unit, Lifting lever for the cutting unit, Lights, Counter, Seat

Page 13

PRESENTATION

Cutting unit

Rider 15T, Rider 15T AWD and Rider 15Ts AWD can be equipped with three different cutting units.

•CombiClip 94

•CombiClip 103

•CombiClip 112

The Combi-unit, equipped with a BioClip-plug, ﬁnely chops the cuttings to fertiliser. Without the BioClip-plug the unit works in the same way as a rear ejection unit.

Lifting lever for the cutting unit

The lift lever is used to set the cutting unit in transport or mowing position.

If the lever is pulled backwards the unit is raised and the blades automatically stop rotating (transport position).

If the lock button is pressed in and the lever is moved forwards the unit will be lowered and the blades will automatically start to rotate (mowing position).

The lever can also be used to temporarily regulate the cutting height, e.g. for a small mound in the lawn.

Cutting height adjustment lever

The cutting height can be adjusted to 7 different positions with the cutting height lever. 25-80 mm

Lights

The lights are switched on and off using the power switch on the control panel.

Counter

The chronometer shows how many hours the engine has been running. Any time when the engine is not running but the ignition is switched on is not registered. The last digit shows tenths of an hour (6 minutes).

Seat

The seat has a jointed attachment on the front edge and can be tipped forward.

The seat can also be adjusted lengthways.

English – 13

Image 13

Contents English Rider 15T Rider 15T AWD Rider 15Ts AWDContents Pre-delivery service Service journalAfter the ﬁrst 8 hours Introduction Symbols KEY to SymbolsKEY to Symbols What is what on the ride-on mower What is WHAT?Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Cutting unit Cutting height adjustment leverLifting lever for the cutting unit LightsFuelling Exercise care and refuel outdoors see safety instructionsRelease lever Clutch control Rider 15T AWD and Rider 15Ts AWDBefore starting DrivingStart the engine Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse orderStop the engine Cutting tipsMaintenance schedule MaintenanceChecking and adjusting the steering wires CleaningRemoving of the machine hoods Checking and adjusting of throttle wire Adjusting the parking brake Rider 15TCan result in reduced braking ability Replacement of fuel ﬁlter Checking and adjusting the choke wireReplacing the air ﬁlter Cool before starting to replace the air ﬁlterIgnition system Checking the fuel pump’s air ﬁlterReplacing the spark plug Check the safety system Main fuse Replacing the light bulbsChecking the tyre pressure Checking the engine’s cooling air intakeFitting the cutting head When the engine is running. Mind your ﬁngersTrapping your hand Lift up the cutting unitRemoving the cutting unit Hands when working with the blades Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit beltsPlacing in the service position Service position for the cutting unitChecking the blades Restoring from service positionRemoving the BioClip plug CombiClip 103, CombiClipChecking the engine’s oil level LubricationChanging the oil ﬁlter Replacing the engine oilChecking the transmission oil level Lubricating the belt adjusterGeneral lubrication Problem Procedure Troubleshooting scheduleStorage ServiceWinter storage GuardTechnical data Cutting unit CombiClip EC-declaration of conformity EC-declaration of conformity Applies to Europe onlyEN ISO 12100-2, EN-836 Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨