Husqvarna manual Fuelling, Release lever, Clutch control Rider 15T AWD and Rider 15Ts AWD

Page 14

PRESENTATION

To adjust move the lever under the front edge of the seat to the left, so that the seat can be moved forward or backwards to the required position.

Fuelling

The engine runs on unleaded petrol with a minimum octane rating of 87 (not mixed with oil). We recommend the use of biodegradable alkylate petrol. (max. methanol 5%, max. ethanol 10%, max. MTBE 15%)

Do not fill the tank completely, leave an expansion area of at least 2.5 cm (1“).

WARNING! Petrol is highly inflammable.

!Exercise care and refuel outdoors (see safety instructions).

IMPORTANT!

Do not use the fuel tank as a support area.

Release lever

The release control must be pulled out in order for the machine to be moved when the engine is shutoff.

Should you attempt to drive the machine with the clutch controls pulled out it will not move. The drive on the axle is disengaged when one of the controls is pulled out.

Pull the controls to the end positions, do not use an intermediate position.

Clutch control Rider 15T AWD and Rider 15Ts AWD

Rider 15T AWD and Rider 15Ts AWD have one control for the front axle and one control for the rear axle.

IMPORTANT!

Always drive the machine with both clutch controls pressed in.

Clutch control, rear axle

-Control drawn out, drive system disengaged.

-Control depressed, drive system engaged.

Clutch control, front axle

The control is positioned on the inside of the left front wheel.

-Rear control (pulled out), drive system disengaged.

-Front control (pushed in), drive system engaged.

Release lever Rider 15T

Pull out the control to disengage the drive system. Push in the control to engage to the drive system.

14 – English

Image 14
Contents Rider 15T Rider 15T AWD Rider 15Ts AWD EnglishContents After the first 8 hours Service journalPre-delivery service Introduction KEY to Symbols SymbolsKEY to Symbols What is WHAT? What is what on the ride-on mowerInsure your Rider Safety InstructionsSafety instructions General useDriving on slopes This is what you doMaintenance ChildrenTransport Presentation Lifting lever for the cutting unit Cutting height adjustment leverCutting unit LightsRelease lever Exercise care and refuel outdoors see safety instructionsFuelling Clutch control Rider 15T AWD and Rider 15Ts AWDStart the engine DrivingBefore starting Driving the Rider Starting the engine with a weak batteryConnecting the jump leads Remove the cables in the reverse orderCutting tips Stop the engineMaintenance Maintenance scheduleRemoving of the machine hoods CleaningChecking and adjusting the steering wires Can result in reduced braking ability Adjusting the parking brake Rider 15TChecking and adjusting of throttle wire Replacing the air filter Checking and adjusting the choke wireReplacement of fuel filter Cool before starting to replace the air filterReplacing the spark plug Checking the fuel pump’s air filterIgnition system Check the safety system Checking the tyre pressure Replacing the light bulbsMain fuse Checking the engine’s cooling air intakeTrapping your hand When the engine is running. Mind your fingersFitting the cutting head Lift up the cutting unitRemoving the cutting unit Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unitHands when working with the blades Replacing the cutting unit beltsService position for the cutting unit Placing in the service positionRemoving the BioClip plug Restoring from service positionChecking the blades CombiClip 103, CombiClipChanging the oil filter LubricationChecking the engine’s oil level Replacing the engine oilGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Troubleshooting schedule Problem ProcedureWinter storage ServiceStorage GuardTechnical data Cutting unit CombiClip EN ISO 12100-2, EN-836 EC-declaration of conformity Applies to Europe onlyEC-declaration of conformity Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨