Husqvarna 15Ts AWD, 15T AWD manual Cutting tips, Stop the engine

Page 17

Driving

4Press in the lock button on the lifting lever and lower the cutting unit.

IMPORTANT INFORMATION

The life span of the drive belts is increased significantly if the engine runs at a low speed when the blades are engaged. Therefore apply full throttle first when the cutting unit has been moved to the mowing position.

Cutting tips

WARNING! Clear the lawn from stones and

!other objects which can be thrown out by the blades.

•Localise and mark stones and other fixed objects to avoid collision.

•Start with a high cutting height and reduce down until the required mowing results are obtained.

•The mowing result will be best with the highest permitted engine speed, see technical data, (the blades rotate rapidly) and low speed (the Rider moves slowly). If the grass is not too high and thick, the driving speed can be increased without noticeably depreciating the mowing result.

•The best lawns are achieved if the grass is cut often. Mowing becomes more uniform and the grass cuttings become more evenly distributed over the surface. The total time consumption is not greater since it is possible to select a higher driving speed without inferior mowing results.

•Avoid mowing a wet lawn. The mowing results are inferior since the wheels sink down into the soft lawn.

•Hose down the cutting unit with water underneath each time it is used. The cutting unit should then be put in the service position.

•When the BioClip function is used, it is very important that the mowing interval is not too long.

!

WARNING! Do not use the machine on

°.

ground that slopes more than 10 Mow

slopes upwards and downwards, never

 

across. Avoid sudden changes in direction.

Stop the engine

Preferably allow the engine to idle for a minute to obtain normal working temperature before stopping it if it has been working hard. Avoid idling the engine for long periods, as there is a risk of carbon build-up on the spark plugs.

1Lift up the cutting unit by pulling the lever backwards to its locked position.

2Move the throttle control to the MIN. position. Turn the ignition key to the ”STOP”.

3When the Rider is at a standstill, press down the parking brake and push in the locking button.

English – 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents English Rider 15T Rider 15T AWD Rider 15Ts AWDContents After the first 8 hours Service journalPre-delivery service Introduction Symbols KEY to SymbolsKEY to Symbols What is what on the ride-on mower What is WHAT?Safety instructions Safety InstructionsInsure your Rider General useThis is what you do Driving on slopesChildren MaintenanceTransport Presentation Cutting unit Cutting height adjustment leverLifting lever for the cutting unit LightsFuelling Exercise care and refuel outdoors see safety instructionsRelease lever Clutch control Rider 15T AWD and Rider 15Ts AWDStart the engine DrivingBefore starting Connecting the jump leads Starting the engine with a weak batteryDriving the Rider Remove the cables in the reverse orderStop the engine Cutting tipsMaintenance schedule MaintenanceRemoving of the machine hoods CleaningChecking and adjusting the steering wires Can result in reduced braking ability Adjusting the parking brake Rider 15TChecking and adjusting of throttle wire Replacement of fuel filter Checking and adjusting the choke wireReplacing the air filter Cool before starting to replace the air filterReplacing the spark plug Checking the fuel pump’s air filterIgnition system Check the safety system Main fuse Replacing the light bulbsChecking the tyre pressure Checking the engine’s cooling air intakeFitting the cutting head When the engine is running. Mind your fingersTrapping your hand Lift up the cutting unitRemoving the cutting unit Hands when working with the blades Adjusting the parallelism of the cutting unitChecking the cutting unit’s parallelism Replacing the cutting unit beltsPlacing in the service position Service position for the cutting unitChecking the blades Restoring from service positionRemoving the BioClip plug CombiClip 103, CombiClipChecking the engine’s oil level LubricationChanging the oil filter Replacing the engine oilGeneral lubrication Lubricating the belt adjusterChecking the transmission oil level Problem Procedure Troubleshooting scheduleStorage ServiceWinter storage GuardTechnical data Cutting unit CombiClip EN ISO 12100-2, EN-836 EC-declaration of conformity Applies to Europe onlyEC-declaration of conformity Page ´z+U+r¶6§¨ Page 1153118-26 ´z+U+r¶6§¨ ´z+U+r¶6§¨
Top Page Image Contents