Ryobi RY09050 Assembling the Blower Tubes, Installing the vacuum bag, Installing the vacuum tubes

Page 9

ASSEMBLY

WARNING:

If any parts are damaged or missing do not operate this product until the parts are replaced. Use of the product with damaged or missing parts could result in possible serious personal injury.

WARNING:

Do not attempt to modify this product or create acces- sories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

WARNING:

To prevent accidental starting that could cause serious personal injury, always disconnect the engine spark plug wire from the spark plug when assembling parts.

ASSEMBLING THE BLOWER TUBES

See Figures 2 - 3.

Align raised tabs on blower housing outlet to the slots on upper tube; slide together and tighten securely by twisting. Check tightness after initial use and retighten if needed.

Attach desired nozzle (high velocity nozzle or sweeper nozzle) to upper blower tube by aligning raised tabs on upper blower tube; slide together and tighten securely by twisting. Check tightness after initial use and retighten if needed.

To remove the tubes, rotate the tubes to unlock them and remove from the blower housing outlet.

Installing the vacuum bag

See Figures 4 - 5.

Remove the nozzle and upper blower tube from the blower by twisting and removing from blower housing outlet.

Unzip the vacuum bag and place the adaptor inside as shown. Push the vacuum bag adaptor through the open- ing opposite the zipper. The wider end of the adaptor will remain on the inside of the vacuum bag when installed properly.

Align the raised slots on the vacuum bag adaptor with the raised locking tabs on the blower housing outlet; push the bag adaptor onto the housing. Twist to lock into place.

Rotate the vacuum bag until the shoulder strap is upright.

Make sure the vacuum bag is zipped and closed before starting the unit.

Installing the vacuum tubes

See Figures 6 - 7.

WARNING:

Contact with rotating impeller blades could result in seri- ous personal injury. Always stop the engine and ensure impeller blades have stopped rotating before opening the vacuum door or installing/changing tubes. Do not put hands or any other object into the vacuum tubes while they are installed on the unit.

To install the vacuum tubes:

Secure the upper and lower vacuum tubes together by aligning the raised locking tabs with the raised slots.

Tap tube assembly on ground until the screw holes in lower tube are in the raised slot of the upper tube. Secure with supplied screws (see figure 1).

Depress door tab using a flathead screwdriver and open vacuum inlet door.

Align tabs on housing with tube assembly.

Turning clockwise, tighten screws on upper vacuum tube to secure to blower housing.

To remove the vacuum tubes:

Loosen screws of the upper vacuum tube by turning counterclockwise.

Remove the vacuum tube assembly from the blower housing.

Close the vacuum inlet cover door securely.

7 - English

Page 8 Page 10
Image 9
Page 8 Page 10
Contents ALL Versions Toutes LES Versions Todas LAS Versiones Save this Manual for Future ReferenceAseguramiento Screw vis, tornillo Manos alejadas de las silenciador Table of Contents Table DES Matières / Índice DE Contenido Read all instructions General Safety RulesFueling Specific Safety RulesSymbol Signal Meaning SymbolsAssembly FeaturesInstalling the vacuum tubes Installing the vacuum bagTo install the vacuum tubes Assembling the Blower TubesOperation Vacuum Operation Operating the BlowerTo start a warm engine To stop the engineGeneral Maintenance MaintenanceCleaning the AIR Filter Cleaning the Exhaust PORT, Muffler and spark arrestorSpark Plug replacement TroubleshootingWhen storing 1 month or longer Problem Cause RemedyLimited Warranty Statement WarrantyMANUFACTURER’S Warranty Coverage This product was manufactured with a catalyst muffler Conserver ces instructions Règles de sécurité généralesApprovisionnement en carburant Règles de sécurité particulièresSymboles Symbole NomExplication Assemblage CaractéristiquesInstallation des tubes d’aspiration Installation DU SAC À DébrisInstallation des tubes d’aspiration Assemblage DES Tubes DE SoufflanteMélange DU Carburant UtilisationRemplissage du réservoir Carburants OxygénésRégulateur DE Vitesse Utilisation DE LA SoufflanteUtilisation de l’aspirateur AVERTISSEMENT  AvertissementEntretien Nettoyage LE Filtre À AIRVoir la et Dépannage REMPLACement de la BougieSAC À Débris Bouchon DU Réservoir AvertissementÉnoncé DE LA Garantie Limitée GarantieResponsabilités DU Propriétaire Dans LE Cadre DE LA Garantie 4050 BesoinGuarde estas instrucciones Reglas de seguridad generalesAbastecimiento de combustible Reglas de seguridad específicasPeligro SímbolosAdvertencia PrecauciónArmado CaracterísticasMontaje DE LOS Tubos DE LA Sopladora Lista de empaquetadoS ta l a c i ó n d e l s a code l a aspiradora Instalación de los tubos de la aspiradoraFuncionamiento Manejo DE LA Sopladora Control DE CruceroManejo DE LA Aspiradora Mantenimiento General MantenimientoLimpieza LA filtro de aire Vea la figura 13 ySaco DE LA Aspiradora Solución de problemasTapa DEL Tanque DE Combustible Advertencia Reemplazo de la BujíaDeclaración DE LA Garantía Limitada GarantíaCobertura DE LA Garantía DEL Fabricante Conjunto DE Silenciador Catalítico Este producto se fabricó con un silenciador catalíticoPage RY09050 Manuel D’UTILISATION Manual DEL Operador

RY09050 specifications

The Ryobi RY09050 is a versatile and efficient outdoor power tool designed for homeowners and landscapers alike. This lightweight and powerful gas-powered string trimmer features a 30cc, 2-cycle engine that offers robust performance for tackling thick grass and tough weeds. Its ergonomic design ensures comfortable handling during extended use, making it a popular choice for those who require a reliable solution for their yard maintenance.

One of the standout features of the RY09050 is its Easy Start technology, which significantly reduces the effort required to start the engine. This innovation allows users to pull the starter cord with less force, making it particularly convenient for those who may find traditional starting methods cumbersome. The inclusion of a straight shaft design enhances reach and maneuverability, enabling users to access hard-to-reach areas such as underneath shrubs and around fences.

The trimmer boasts a 17-inch cutting width, allowing users to cover a wide area with each pass, ultimately saving time on larger properties or extensive landscaping projects. Additionally, the RY09050 is equipped with a dual-line bump feed head that enables quick and easy line advancements, allowing users to maintain productivity without frequent interruptions.

Another significant characteristic of the Ryobi RY09050 is its lightweight construction. Weighing only about 10 pounds, it is easy to handle and transport, while still delivering the power and durability expected from a Ryobi product. Furthermore, the unit is designed with an adjustable handle, allowing users to customize their grip for optimal comfort and control.

Ryobi is known for integrating user-friendly technologies in its products, and the RY09050 is no exception. It features a translucent fuel tank, which allows users to easily monitor fuel levels at a glance, reducing the risk of running out of gas unexpectedly. The trimmer also has a handy storage hook, making it convenient to hang and store when not in use, saving space in the garage or shed.

Overall, the Ryobi RY09050 combines power, efficiency, and convenience, making it an excellent choice for tackling outdoor trimming tasks. With its impressive features and user-friendly design, it stands out in the competitive market of string trimmers, catering to both novice homeowners and experienced landscapers.
Top Page Image Contents