Remington 100582-01, 100582-02, EL-7B owner manual Sharpening Cutters, Filing Cutter Depth Gauges

Page 13

CLEANING AND MAINTENANCE

Continued

Sharpening Cutters

Use file guide for 30° filing.

1.Adjust chain for proper tension (see Saw Chain Tension Adjustment, page 7).

2.Clamp guide bar in vise to hold saw steady. Note: Do not clamp chain.

3.Press four millimeter (5/32") round file (attached to file guide) into groove between top plate and depth gauge on chain. File guide should rest on both top plate and depth gauge (see Figures 20 and 21). Note: File at midpoint of guide bar.

4.Hold file guide level. Make sure 30° mark on file guide is parallel to center of guide bar (see Figure 20). This will insure that you file cutters at 30° angle.

5.File from inside towards outside of cutter until sharp. Only file in this one direction (see Figure 20). Note: Two or three strokes with file should sharpen cutter.

6.After each cutter if sharpened, move chain forward to sharpen next cutter. File all cutters on one side of chain.

7.Move to other side of chain and repeat process.

Filing

Direction

30° Guide

Mark

File Guide

 

Top Plate

Left Side

Groove (right side of chain)

 

of Chain

Depth Gauge

 

 

(left side

 

of chain)

Groove

Top Plate

Depth Gauge

(left side

(right side of chain)

of chain)

 

 

Right Side

 

of Chain

Figure 21 - Chain Part Locations

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpening, reset cutter depth gauges.

1.Place depth gauge tool firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure 22).

2.Use medium flat file. File depth gauge level with depth gauge tool.

3.Remove depth gauge tool. With flat file, round off front corner of cutter depth gauge (see Figure 23).

Depth Gauge

4 mm (5/32") Round File

Note: This illustration shows file guide place- ment and filing direction for

Flat File

Depth

Gauge

Tool

Depth

Gauge

Slot

sharpening cutters on left side of chain.

Figure 20 - File and File Guide Placement On Chain

Figure 22 - Depth Gauge Tool On Chain

Front Corner

ECSp005

Figure 23 - Round Off Front Corner Of Depth Gauge

After several hand filings, have authorized service center or sharpening service machine sharpen chain. This will insure even filing.

101241

13

Continued

 

 

 

Image 13
Contents Chain Brake ContentsInformation SymbolsKickback Safety Devices On This Saw Safety WarningsBefore Operating Chain SAW Cause Of KickbackMaintenance and Storage of Chain SAW Saw Maintenance and Kickback SafetyPushback and PULL-IN Cause Of Pushback and Pull-InChain SAW Names and Terms Product IdentificationGuide Bar Nuts Sprocket Support Adjusting Hole AssemblySprocket Support Adjusting Block Plate Screw UnpackingFilling OIL Tank SAW Chain Tension AdjustmentGuide Bar Nuts Correct Gap Tension Incorrect Tension Extension Cords Operating Chain SAWOiling Chain Chain BrakeFelling a Tree Cutting Down a Tree Trimming a Tree PruningBefore Felling a Tree Retreat Path Direction of Fall TreeLimbing a Tree Felling Procedure1st Cut Inches Lower Notch CutLog Supported On One End Bucking a LOGEntire Length Of Log On Ground Log Supported On Both EndsCleaning SAW Body Cleaning and MaintenanceCare of Guide BAR Sharpening Your SAW ChainFiling Cutter Depth Gauges Sharpening CuttersStorage Replacement PartsReplacing Saw Chain Observed Fault Possible Cause Remedy Troubleshooting101241 101241 Keep this Warranty Warranty InformationLimited Warranty Electric Chain SAW Table DES Matières Frein DE ChaîneDescription SymbolesAvant D’UTILISER LA Tronç Onneuse AvertissementRecul Cause du reculCauses de la poussé e et de la traction Poussé E ET TractionEntretien de la tronç onneuse et protection contre le recul Utilisation DE LA Tronç OnneuseEntretien ET Remisage DE LA Tronç Onneuse Vocabulaire DE LA Tronç Onneuse Nomenclature DES PIÈ CESAssemblage Avertissement DÉ BallageSupport de pignon Bloc de Plaque de Réglage Vis de réglage Remplissage DU RÉ Servoir D’HUILE RÉ Glage DE LA Tension DE LA Chaîne AvertissementProlongateurs DE Cordon Utilisation DE LA Tronç Onneuse AvertissementLubrification DE LA Chaîne Sciage Avec LA Tronç OnneuseFrein DE Chaîne Utilisation DE LA Tronç OnneuseTaille D’UN Arbre É lagage Avant d’abattre un arbre Abattage D’UN ArbreProcé dure d’abattage Sifflet d’abattage Trait d’abattageDirection de la BranchageChute La bille est soutenue à une extré mité Tronç Onnage D’UNE BilleToute la bille repose au sol La bille est soutenue aux deux extré mité sNettoyage DU Carter DE Tronç Onneuse Nettoyage ET Entretien AvisEntretien normal de la lame-guide Entretien DE LA LAME-GUIDEAffû Tage DE LA Chaîne Nettoyage ET EntretienOutils né cessaires pour affû ter la chaîne Affû tage des taillantsRemisage Remplacement de la chaînePIÈ CES DE Rechange Avertissement Limage des limiteurs de profondeur des taillantsDÉ Faillance Observé E Cause Possible Remè DE DÉ Pannage AvertissementConserver Cette Garantie Information SUR LA GarantieGarantie Limité E SUR LA Tronç Onneuse É Lectrique