Bosch Power Tools 1608LX Maintenance and Service, Tool Lubrication, Carbon Brushes, Bearings

Page 11

Maintenance and Service

WARNING! Preventive maintenance per- formed by unauthorized personnel may result in misplacing of internal wires and compo- nents which could cause serious hazard. We recommend that all tool service be performed at a Bosch Factory Service Center.

Tool Lubrication

Your Bosch tool has been properly lubricated and is ready for use. We recommend, that tools with gears be regreased with a special gear lubricant every time the brushes are changed.

Carbon Brushes

The brushes and commutator in your Bosch tool have been engineered for many hours of dependable service. To maintain peak effi- ciency of the motor, we recommend that every two to six months the brushes be examined. Only genuine Bosch replacement brushes spe- cially designed for your tool should be used.

Bearings

After about 300-400 hours of operation, or at every second brush change, the bearings should be replaced at a Bosch Factory Service Center. Bearings which become noisy (due to heavy load or very abrasive material cutting) should be replaced at once to avoid overheating and motor failure.

Cleaning

WARNING! To avoid accidents, always dis- connect the tool from the power supply before cleaning or performing any maintenance. The tool may be cleaned most effectively with compressed air. Always wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not attempt to clean by inserting pointed objects through openings.

CAUTION! Certain cleaning agents and sol- vents damage plastic parts. Some of these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and household detergents that contain ammonia.

NOTES:

11

BM 2610909755 7/01

11

7/26/01, 12:03 PM

Image 11

Contents BM 2610909755 7/01 26/01, 1203 PM BM 2610909755 7/01 26/01, 1203 PM Standard EQUIPMENT-ALL Models Accessory ListingProduct Data Trim Router Trim Router ComponentsWork Area General Safety RulesFor all Power Tools Personal SafetySafety Rules for Trim Router Operating the Tool Slide ON/OFF SwitchDouble Insulated Tools Extension CordsAssembling Motor to Base All Models Except Model 1609A Depth Adjustment Model 1608, 1608LX OnlyModel 1609A Only Collet CareUnderscribe Trimmer-Model 1608U Laminate Trim Guide1608T Templet Guides Using Self-Piloted BitsOffset Trimmer Model 1609A Feed Trimming TipsWork Cutter Carbon Brushes Maintenance and ServiceCleaning Tool LubricationBosch Power Tool Company Limited Warranty WarrantyÉquipement Standard Tous LES Modèles AccessoiresFiche technique Toupie ébarbeuse Composants de la toupie ébarbeuseSécurité personnelle Règles Générales DE SécuritéPour tous les outils motorisés Lieu de travailRègles de sécurité concernant La toupie ébarbeuse Rallonges Outils à double isolationSoin de la douille Mode d’emploiInterrupteur marche-arrêt Modèle 1609A seulementGuide d’ébarbage de stratifiés Moteur 1609A seulementRéglage de la profondeur Modèles 1608, 1608LX seulement Ébarbeuse de sous-trusquinage Modèle 1608U Guides de gabarit Ébarbeuse déportée Modèle 1609AUsage de fers autoguidés La mise en marche et glissez l’interrupteur Conseils pratiquesBalais de charbon Maintenance et entretienRoulements Nettoyage Graissage de l’outilRemarques Garantie Garantie Limitée Bosch Power Tool CompanyEquipo ESTANDAR-TODOS LOS Modelos Datos del producto Fresadora de recortarLista de accesorios Componentes de la fresadora de recortarSeguridad personal Normas Generales DE SeguridadPara todas las herramientas Mecánicas Area de trabajoNormas de seguridad para la Fresadora de recortar Herramientas con aislamiento doble Interruptor corredizo ON/OFF De encendido y apagado Cordones de extensiónFuncionamiento de la Herramienta Cuidado del portaherramienta Modelo 1609A únicamenteGuía de recortar material laminar Ajuste de profundidad Modelos 1608 y 1608LX únicamenteRecortadora para trazar por debajo Modelo 1608U Consejos para recortar Recortadora orientable Modelo 1609AUtilización de brocas autopilotadas Guías de plantillaRodamientos Mantenimiento y servicioLubricación de las herramientas Escobillas de carbónNotas 610 909 Garantia