Bosch Power Tools 1608LX instruction manual Trimming Tips, Work Cutter, Feed

Page 10

Fig. 17

WARNING! Use of any accessory not speci- fied in this manual or the BOSCH catalog for use with this tool may create a hazard.

Trimming Tips

Your Bosch trim router is designed to trim laminates, phenolics, or other materials which have been bonded to a substrate and overhang by about 1/8" (3 mm). It is also handy for light edge forming, grooving, and sign making with 1/4" shank bits. Be sure the workpiece is se- cure, and clamp it in place if necessary. With the tool properly assembled and adjusted, be certain that the switch is in the “OFF” position, and connect to the power source. Grasp the motor housing firmly to resist starting torque, and slide switch 3 to the “ON” position. With the motor running at full speed, place the base of the trimmer on the work surface and feed the bit with a smooth steady motion into the mate- rial to be cut. The correct relationship between the direction of bit or cutter rotation and router feed is shown in Fig 18; feed in this direction or chatter will result.

Fig. 18
WORK
CUTTER	DIRECTION
	OF FEED

Support the router on the long edge of the base whenever possible for maximum stability. At the completion of the cut, slide switch to the “OFF” position and allow the bit to come to a complete stop before setting the tool down. When using edge forming bits, it may be nec- essary to make the cut in more than one pass with progressively deeper settings to avoid overloading the motor. If the bit cuts freely and the motor does not slow down, the cutting depth is generally correct.

10

BM 2610909755 7/01

10

7/26/01, 12:03 PM

Image 10

Contents BM 2610909755 7/01 26/01, 1203 PM BM 2610909755 7/01 26/01, 1203 PM Trim Router Components Accessory ListingProduct Data Trim Router Standard EQUIPMENT-ALL ModelsPersonal Safety General Safety RulesFor all Power Tools Work AreaSafety Rules for Trim Router Extension Cords Slide ON/OFF SwitchDouble Insulated Tools Operating the ToolCollet Care Depth Adjustment Model 1608, 1608LX OnlyModel 1609A Only Assembling Motor to Base All Models Except Model 1609A1608T Laminate Trim GuideUnderscribe Trimmer-Model 1608U Offset Trimmer Model 1609A Using Self-Piloted BitsTemplet Guides Work Cutter Trimming TipsFeed Tool Lubrication Maintenance and ServiceCleaning Carbon BrushesWarranty Bosch Power Tool Company Limited WarrantyComposants de la toupie ébarbeuse AccessoiresFiche technique Toupie ébarbeuse Équipement Standard Tous LES ModèlesLieu de travail Règles Générales DE SécuritéPour tous les outils motorisés Sécurité personnelleRègles de sécurité concernant La toupie ébarbeuse Outils à double isolation RallongesModèle 1609A seulement Mode d’emploiInterrupteur marche-arrêt Soin de la douilleRéglage de la profondeur Modèles 1608, 1608LX seulement Moteur 1609A seulementGuide d’ébarbage de stratifiés Ébarbeuse de sous-trusquinage Modèle 1608U Usage de fers autoguidés Ébarbeuse déportée Modèle 1609AGuides de gabarit Conseils pratiques La mise en marche et glissez l’interrupteurNettoyage Graissage de l’outil Maintenance et entretienRoulements Balais de charbonRemarques Garantie Limitée Bosch Power Tool Company GarantieComponentes de la fresadora de recortar Datos del producto Fresadora de recortarLista de accesorios Equipo ESTANDAR-TODOS LOS ModelosArea de trabajo Normas Generales DE SeguridadPara todas las herramientas Mecánicas Seguridad personalNormas de seguridad para la Fresadora de recortar Herramientas con aislamiento doble Funcionamiento de la Herramienta Cordones de extensiónInterruptor corredizo ON/OFF De encendido y apagado Modelo 1609A únicamente Cuidado del portaherramientaAjuste de profundidad Modelos 1608 y 1608LX únicamente Guía de recortar material laminarRecortadora para trazar por debajo Modelo 1608U Guías de plantilla Recortadora orientable Modelo 1609AUtilización de brocas autopilotadas Consejos para recortarEscobillas de carbón Mantenimiento y servicioLubricación de las herramientas RodamientosNotas Garantia 610 909