Craftsman 247.77013.0 manual Attaching the Hose Assembly, Attaching the BAG

Page 10

ASSEMBLY

ATTACHING THE HOSE ASSEMBLY

		1.	a. Slide hose adapter of hose assembly into the base adapter
			located on the left front of the Yard Vacuum. See Figure 5.
			b. Pull spring loaded pin out on the base and align pin with the first
			hole (closest to the end of the tube) in the hose adapter.
	A		c. Release the pin to lock the hose in place.
	A	2.	a. Snap the hose handle first into the upper hose handle bracket
		B	and then into the lower hose handle bracket.
		B	b. Lay hose tubing on hanger bracket next to chipper chute. See

			Figure 6.
	Align pin	ATTACHING THE BAG
	with this	1.	Grasp bag handle with one hand and slide locking rod on mounting
	hole.	1.
	hole.		bracket with other hand toward engine. Use the end of mounting

	bracket as leverage when sliding the locking rod.
	a.	Slip bag over the rim of the discharge opening and release
		locking rod to secure bag in place. See Figure 7.
Figure 5	b. Snap bag clip to the top of the lower handle.
	b. Snap bag clip to the top of the lower handle.
	c.	Place the lower straps on the bag over the top of lower handle,
		hooking them on the studs. See Figure 7.

NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on bag handle when securing the bag or engine will not start.

B

A

A

B

C

Figure 6

Figure 7

10

Image 10

Contents Operator’s Manual Warranty Table of ContentsProduct Specifications Model Number Repair Protection Agreement Training Safety InstructionsPreparation Operation Maintenance & StorageDo not modify engine This page left intentionally blank Safety Labels To Avoid Serious InjuryRemoving Unit from Carton AssemblyOpening Carton Loose Parts in CartonAttaching the Handle Attaching the Hose Assembly Attaching the BAGNozzle Height Adjustment Attaching the Blower ChuteOperation GAS and OIL FILL-UP To Stop Engine Attach spark plug wire and rubber boot to spark plugTo Start Engine To Empty BAGUsing the Hose Assembly Using the Nozzle VacuumTo Remove Blower Chute Servicing the Air Cleaner Service and MaintenanceEngine Maintenance General RecommendationsClean Equipment LubricationDrive Control Cable Adjustment Removing the Flail ScreenRemove bag assembly or blower chute Disconnect and ground the spark plug wire to retaining postSharpening or Replacing Chipper Blade Nuts Impeller Gas in the tank † Under heavy load or in high temperatures Maintenance ScheduleEach Use Engine oil level Check Preparing the Engine OFF-SEASON StoragePreparing the yard vacuum Troubleshooting Parts List Description 710-165012 B 21 a 631-0090 Blower Chute 723-0400 Safety Glasses Not Shown 1 11 10Spring-Valve Exhaust Cylinder AssemblySpring-Valve Intake 694086 Guard-FlywheelHousing-Blower 691753 Bracket-Air Cleaner Primer272653†*†† Gasket-Air Cleaner 695161 Cup/Screen AssemblyCover-Blower Housing Guard-Rewind 617 270344†*†† Seal-O Ring Intake Manifold Switch-Stop66538 Boot-Spark Plug 498144 Assembly-Pulley/Spring PulleySears Emission Control Defects Warranty Provisions Sears Emission Control Defects Warranty CoverageOwner’s Warranty Responsibilities This page applicable in the U.S.A. and Canada onlyPage Especificaciones DEL Producto ÍndiceGarantía Número DE ModeloAcuerdo DE Protección Para Reparaciones Capacitación Instrucciones DE SeguridadPreparativos Mantenimiento y almacenamiento OperaciónNo modifique el motor Cómo Sacar LA Unidad DE LA Caja MontajeApertura DE LA Caja DE Cartón Piezas Sueltas Dentro DE LA CajaLos pernos del carro deben estar colocados de forma Montaje DE LA ManijaBroches de horquilla. Vea la figura Adecuada en la manija. Vea la figuraManguera Instalación DEL Montaje DE LAMontaje DE LA Bolsa Ajuste DE LA Altura DEL Pico Instalar EL Canal DE SopladoLibere la palanca hacia la cubierta Operación Llenado DE Gasolina Y Aceite Para Encender EL Motor Para Detener EL MotorUSO DEL Pico DE LA Aspiradora Descarga DE LA BolsaExtracción DEL Canal DE Soplado USO DEL Montaje DE LA MangueraMantenimiento de Motor Servicio Y MantenimientoRecomendaciones Generales Servicio a La BujíaLubricación Limpieza DEL EquipoAjuste del Cable del Control de Transmisiòn Extracción DE LA Pantalla DE DES- GranadoAfilado O Reemplazo DE LAS Hojas DE LA Cortadora Retire el montaje de la bolsa o el canal de sopladoTornillos de cabeza plana Cada Uso Nivel del aceite de motor Comprobar Lista DE MantenimientoTanque † Bajo carga pesada o en temperaturas altas La preparación del vacío de yarda Almacenamiento Fuera DE TemporadaPreparación del Motor Ya que los motores almacenaron más de 30 díasSolución DE Problemas Motor y alojamiento de soplador El motor recalienta El nivel de aceite del motor es bajoFlujo de aire restringido Quite la bujía y ajuste el huecoEsta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Notas MY-HOME1-800-469-4663 Call anytime, day or night