Craftsman 247.77013.0 manual Safety Instructions, Training, Preparation

Page 4

SAFETY INSTRUCTIONS

WARNING

This symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or property of yourself and others. Read and follow all instructions in this manual before

attempting to operate this machine. Failure to comply with these instructions may result in personal injury. When you see this symbol,

HEED ITS WARNING!

Your Responsibility: Restrict the use of this power machine to persons who read, understand, and follow the warnings and instruc- tions in this manual and on the machine.

DANGER

This machine was built to be operated according to the rules for safe operation in this manual. As with any type of power equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death.

WARNING

Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to State of California to cause cancer and birth defects or other reproductive harm.

Training

Read, understand, and follow all instructions on the machine and in the manual(s) before attempting to assemble and operate. Keep this manual in a safe place for future and regular reference and for ordering replacement parts.

Be familiar with all controls and their proper operation. Know how to stop the machine and disengage them quickly.

Never allow children under 16 years old to operate this machine. Chil- dren 16 years old and over should read and understand the operation instructions and safety rules in this manual and should be trained and supervised by a parent.

Never allow adults to operate this machine without proper instruction.

Keep bystanders, helpers, pets, and children at least 75 feet from the machine while it is in operation. Stop machine if anyone enters the area.

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon monoxide, an odorless and deadly gas.

Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

Never attempt to unclog either the feed intake or discharge opening, remove or empty vacuum bag, or inspect and repair the machine while the engine is running. Shut the engine off and wait until all moving parts have come to a complete stop. Disconnect the spark plug wire and ground it against the engine.

Preparation

Thoroughly inspect the area where the equipment is to be used. Remove all rocks, bottles, cans, or other foreign objects which could be picked up or thrown and cause personal injury or damage to the machine.

Always wear safety glasses or safety goggles during operation or while performing an adjustment or repair, to protect eyes. Thrown objects which ricochet can cause serious injury to the eyes.

Wear sturdy, rough-soled work shoes and close-fitting slacks and shirts. Loose fitting clothes or jewelry can be caught in movable parts. Never operate this machine in bare feet or sandals. Wear leather work gloves when feeding material in the chipper chute.

Before starting, check all bolts and screws for proper tightness to be sure the machine is in safe working condition. Also, visually inspect machine for any damage at frequent intervals.

Maintain or replace safety and instructions labels, as necessary.

To avoid personal injury or property damage use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Serious personal injury can occur when gasoline is spilled on yourself or your clothes which can ignite. Wash your skin and change clothes immediately.

Use only an approved gasoline container.

Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

Never fuel machine indoors.

Never remove gas cap or add fuel while the engine is hot or running.

Allow engine to cool at least two minutes before refueling.

Never over fill fuel tank. Fill tank to no more than 1/2 inch below bottom of filler neck to provide space for fuel expansion.

Replace gasoline cap and tighten securely.

If gasoline is spilled, wipe it off the engine and equipment. Move machine to another area. Wait 5 minutes before starting the engine.

Never store the machine or fuel container inside where there is an open flame, spark, or pilot light (e.g. furnace, water heater, space heater, clothes dryer, etc.).

To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil or fuel spillage and remove any fuel soaked debris.

Allow machine to cool at least 5 minutes before storing.



Image 4
Contents Operator’s Manual Warranty Table of ContentsProduct Specifications Model Number Repair Protection Agreement Training Safety InstructionsPreparation Operation Maintenance & StorageDo not modify engine This page left intentionally blank Safety Labels To Avoid Serious InjuryAssembly Opening CartonRemoving Unit from Carton Loose Parts in CartonAttaching the Handle Attaching the Hose Assembly Attaching the BAGNozzle Height Adjustment Attaching the Blower ChuteOperation GAS and OIL FILL-UP Attach spark plug wire and rubber boot to spark plug To Start EngineTo Stop Engine To Empty BAGUsing the Hose Assembly Using the Nozzle VacuumTo Remove Blower Chute Service and Maintenance Engine MaintenanceServicing the Air Cleaner General RecommendationsClean Equipment LubricationDrive Control Cable Adjustment Removing the Flail ScreenRemove bag assembly or blower chute Disconnect and ground the spark plug wire to retaining postSharpening or Replacing Chipper Blade Nuts Impeller Gas in the tank † Under heavy load or in high temperatures Maintenance ScheduleEach Use Engine oil level Check Preparing the Engine OFF-SEASON StoragePreparing the yard vacuum Troubleshooting Parts List Description 710-165012 B 21 a 631-0090 Blower Chute 723-0400 Safety Glasses Not Shown  1 11 10Cylinder Assembly Spring-Valve IntakeSpring-Valve Exhaust 694086 Guard-Flywheel691753 Bracket-Air Cleaner Primer 272653†*†† Gasket-Air CleanerHousing-Blower 695161 Cup/Screen Assembly617 270344†*†† Seal-O Ring Intake Manifold Switch-Stop 66538 Boot-Spark PlugCover-Blower Housing Guard-Rewind 498144 Assembly-Pulley/Spring PulleySears Emission Control Defects Warranty Coverage Owner’s Warranty ResponsibilitiesSears Emission Control Defects Warranty Provisions This page applicable in the U.S.A. and Canada onlyPage Índice GarantíaEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Capacitación Instrucciones DE SeguridadPreparativos Mantenimiento y almacenamiento OperaciónNo modifique el motor Montaje Apertura DE LA Caja DE CartónCómo Sacar LA Unidad DE LA Caja Piezas Sueltas Dentro DE LA CajaMontaje DE LA Manija Broches de horquilla. Vea la figuraLos pernos del carro deben estar colocados de forma Adecuada en la manija. Vea la figuraManguera Instalación DEL Montaje DE LAMontaje DE LA Bolsa Ajuste DE LA Altura DEL Pico Instalar EL Canal DE SopladoLibere la palanca hacia la cubierta Operación Llenado DE Gasolina Y Aceite Para Encender EL Motor Para Detener EL MotorDescarga DE LA Bolsa Extracción DEL Canal DE SopladoUSO DEL Pico DE LA Aspiradora USO DEL Montaje DE LA MangueraServicio Y Mantenimiento Recomendaciones GeneralesMantenimiento de Motor Servicio a La BujíaLubricación Limpieza DEL EquipoAjuste del Cable del Control de Transmisiòn Extracción DE LA Pantalla DE DES- GranadoAfilado O Reemplazo DE LAS Hojas DE LA Cortadora Retire el montaje de la bolsa o el canal de sopladoTornillos de cabeza plana Cada Uso Nivel del aceite de motor Comprobar Lista DE MantenimientoTanque † Bajo carga pesada o en temperaturas altas Almacenamiento Fuera DE Temporada Preparación del MotorLa preparación del vacío de yarda Ya que los motores almacenaron más de 30 díasSolución DE Problemas El motor recalienta El nivel de aceite del motor es bajo Flujo de aire restringidoMotor y alojamiento de soplador Quite la bujía y ajuste el huecoEsta página se aplica sólo en EE.UU. y Canadá Piezas con garantíaMotor certificado Notas MY-HOME1-800-469-4663 Call anytime, day or night