Craftsman 247.77013.0 manual Attaching the Blower Chute, Nozzle Height Adjustment

Page 11

ASSEMBLY

ATTACHING THE BLOWER CHUTE

NOTE: The bag must be removed before installing the blower chute.

1.a. Grasp blower chute with one hand and slide locking rod on mounting bracket with other hand toward engine. Use the end of mounting bracket as leverage when sliding the locking rod. See Figure 8.

b.Slip blower chute over rim of discharge opening and release locking rod to secure chute in place, as in Figure 8.

c.Raise the nozzle height to the highest setting when using the blower chute. Refer to nozzle height adjustment below.

NOTE: The bag/chute switch button attached to the mounting bracket must be fully depressed by the tip of front tab on the blower chute or engine will not start.

A

B

WARNING

Always stop engine and disconnect spark plug wire before performing any maintenance or adjustments. Always wear safety glasses during operation or while performing any adjustments or repairs.

NOZZLE HEIGHT ADJUSTMENT

The nozzle can be adjusted to any five positions, ranging from 5/8” to 4 1/8” ground clearance. The nozzle height has to be adjusted according to yard conditions.

1.Depress nozzle height adjustment lever towards wheel. See Figure 9.

2.Move the height adjustment lever forward or backward to adjust the nozzle upwards or downwards. Make sure both levers are in the same position.

3.Release lever towards deck.

NOTE: In general, raise the nozzle height to vacuum a thick layer of leaves or to operate with the blower chute. Lower the nozzle height for smoother surfaces.

B

Figure 8

Figure 9

11

Image 11

Contents Operator’s Manual Product Specifications Model Number Table of ContentsWarranty Repair Protection Agreement Preparation Safety InstructionsTraining Do not modify engine Maintenance & StorageOperation This page left intentionally blank To Avoid Serious Injury Safety LabelsLoose Parts in Carton AssemblyOpening Carton Removing Unit from CartonAttaching the Handle Attaching the BAG Attaching the Hose AssemblyAttaching the Blower Chute Nozzle Height AdjustmentOperation GAS and OIL FILL-UP To Empty BAG Attach spark plug wire and rubber boot to spark plugTo Start Engine To Stop EngineTo Remove Blower Chute Using the Nozzle VacuumUsing the Hose Assembly General Recommendations Service and MaintenanceEngine Maintenance Servicing the Air CleanerLubrication Clean EquipmentRemoving the Flail Screen Drive Control Cable AdjustmentSharpening or Replacing Chipper Blade Disconnect and ground the spark plug wire to retaining postRemove bag assembly or blower chute Nuts Impeller Each Use Engine oil level Check Maintenance ScheduleGas in the tank † Under heavy load or in high temperatures Preparing the yard vacuum OFF-SEASON StoragePreparing the Engine Troubleshooting Parts List 710-1650 Description12 B 21 a 631-0090 Blower Chute 723-0400 Safety Glasses Not Shown 1 10 11694086 Guard-Flywheel Cylinder AssemblySpring-Valve Intake Spring-Valve Exhaust695161 Cup/Screen Assembly 691753 Bracket-Air Cleaner Primer272653†*†† Gasket-Air Cleaner Housing-Blower498144 Assembly-Pulley/Spring Pulley 617 270344†*†† Seal-O Ring Intake Manifold Switch-Stop66538 Boot-Spark Plug Cover-Blower Housing Guard-RewindThis page applicable in the U.S.A. and Canada only Sears Emission Control Defects Warranty CoverageOwner’s Warranty Responsibilities Sears Emission Control Defects Warranty ProvisionsPage Número DE Modelo ÍndiceGarantía Especificaciones DEL ProductoAcuerdo DE Protección Para Reparaciones Preparativos Instrucciones DE SeguridadCapacitación No modifique el motor OperaciónMantenimiento y almacenamiento Piezas Sueltas Dentro DE LA Caja MontajeApertura DE LA Caja DE Cartón Cómo Sacar LA Unidad DE LA CajaAdecuada en la manija. Vea la figura Montaje DE LA ManijaBroches de horquilla. Vea la figura Los pernos del carro deben estar colocados de formaMontaje DE LA Bolsa Instalación DEL Montaje DE LAManguera Libere la palanca hacia la cubierta Instalar EL Canal DE SopladoAjuste DE LA Altura DEL Pico Operación Llenado DE Gasolina Y Aceite Para Detener EL Motor Para Encender EL MotorUSO DEL Montaje DE LA Manguera Descarga DE LA BolsaExtracción DEL Canal DE Soplado USO DEL Pico DE LA AspiradoraServicio a La Bujía Servicio Y MantenimientoRecomendaciones Generales Mantenimiento de MotorLimpieza DEL Equipo LubricaciónExtracción DE LA Pantalla DE DES- Granado Ajuste del Cable del Control de TransmisiònRetire el montaje de la bolsa o el canal de soplado Afilado O Reemplazo DE LAS Hojas DE LA CortadoraTornillos de cabeza plana Tanque † Bajo carga pesada o en temperaturas altas Lista DE MantenimientoCada Uso Nivel del aceite de motor Comprobar Ya que los motores almacenaron más de 30 días Almacenamiento Fuera DE TemporadaPreparación del Motor La preparación del vacío de yardaSolución DE Problemas Quite la bujía y ajuste el hueco El motor recalienta El nivel de aceite del motor es bajoFlujo de aire restringido Motor y alojamiento de sopladorPiezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Notas Call anytime, day or night MY-HOME1-800-469-4663