Craftsman 247.77013.0 manual Attaching the Handle

Page 9

ASSEMBLY

ATTACHING THE HANDLE

1.Remove the hairpin clips from the handle brackets and remove the carriage screws and wing nuts from the lower handle.

a.Place the bottom holes in lower handle over the pins on the handle brackets and secure with hairpin clips. See Figure 2.

b.Insert carriage screws through upper hole in lower handle from the inside and secure with wing nuts. See Figure 2.

2. a. Unfold the upper handle until it aligns with lower handle. Make sure the rope guide is on the right side of upper handle. See Figure 3.

IMPORTANT: Make sure the cables are routed outside the lower handle. Also, do not crimp the cables while lifting up the handles.

b.Secure the two handles by tightening the handle knobs (carriage bolts must be seated properly into the handle). See Figure 3.

3.Pull the two cable ties attached to the cables tight approximately

8 inches from each cable end and place the cables into the cable guide.

4.Loosen the wing nut that secures the rope guide to the right side of upper handle.

a.Pull the starter rope out of the engine slowly. See Figure 4.

b.Slip the starter rope into the rope guide. Tighten the wing nut. See Figure 4.

Figure 2

Rope Guide

B

A

Figure 3

B

A

Figure 4



Image 9
Contents Operator’s Manual Table of Contents WarrantyProduct Specifications Model Number Repair Protection Agreement Safety Instructions TrainingPreparation Maintenance & Storage OperationDo not modify engine This page left intentionally blank To Avoid Serious Injury Safety LabelsOpening Carton AssemblyRemoving Unit from Carton Loose Parts in CartonAttaching the Handle Attaching the BAG Attaching the Hose AssemblyAttaching the Blower Chute Nozzle Height AdjustmentOperation GAS and OIL FILL-UP To Start Engine Attach spark plug wire and rubber boot to spark plugTo Stop Engine To Empty BAGUsing the Nozzle Vacuum Using the Hose AssemblyTo Remove Blower Chute Engine Maintenance Service and MaintenanceServicing the Air Cleaner General RecommendationsLubrication Clean EquipmentRemoving the Flail Screen Drive Control Cable AdjustmentDisconnect and ground the spark plug wire to retaining post Remove bag assembly or blower chuteSharpening or Replacing Chipper Blade Nuts Impeller Maintenance Schedule Gas in the tank † Under heavy load or in high temperaturesEach Use Engine oil level Check OFF-SEASON Storage Preparing the EnginePreparing the yard vacuum Troubleshooting Parts List 710-1650 Description12 B 21 a 631-0090 Blower Chute 723-0400 Safety Glasses Not Shown  1 10 11Spring-Valve Intake Cylinder AssemblySpring-Valve Exhaust 694086 Guard-Flywheel272653†*†† Gasket-Air Cleaner 691753 Bracket-Air Cleaner PrimerHousing-Blower 695161 Cup/Screen Assembly66538 Boot-Spark Plug 617 270344†*†† Seal-O Ring Intake Manifold Switch-StopCover-Blower Housing Guard-Rewind 498144 Assembly-Pulley/Spring PulleyOwner’s Warranty Responsibilities Sears Emission Control Defects Warranty CoverageSears Emission Control Defects Warranty Provisions This page applicable in the U.S.A. and Canada onlyPage Garantía ÍndiceEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Instrucciones DE Seguridad CapacitaciónPreparativos Operación Mantenimiento y almacenamientoNo modifique el motor Apertura DE LA Caja DE Cartón MontajeCómo Sacar LA Unidad DE LA Caja Piezas Sueltas Dentro DE LA CajaBroches de horquilla. Vea la figura Montaje DE LA ManijaLos pernos del carro deben estar colocados de forma Adecuada en la manija. Vea la figuraInstalación DEL Montaje DE LA MangueraMontaje DE LA Bolsa Instalar EL Canal DE Soplado Ajuste DE LA Altura DEL PicoLibere la palanca hacia la cubierta Operación Llenado DE Gasolina Y Aceite Para Detener EL Motor Para Encender EL MotorExtracción DEL Canal DE Soplado Descarga DE LA BolsaUSO DEL Pico DE LA Aspiradora USO DEL Montaje DE LA MangueraRecomendaciones Generales Servicio Y MantenimientoMantenimiento de Motor Servicio a La BujíaLimpieza DEL Equipo LubricaciónExtracción DE LA Pantalla DE DES- Granado Ajuste del Cable del Control de TransmisiònRetire el montaje de la bolsa o el canal de soplado Afilado O Reemplazo DE LAS Hojas DE LA CortadoraTornillos de cabeza plana Lista DE Mantenimiento Cada Uso Nivel del aceite de motor ComprobarTanque † Bajo carga pesada o en temperaturas altas Preparación del Motor Almacenamiento Fuera DE TemporadaLa preparación del vacío de yarda Ya que los motores almacenaron más de 30 díasSolución DE Problemas Flujo de aire restringido El motor recalienta El nivel de aceite del motor es bajoMotor y alojamiento de soplador Quite la bujía y ajuste el huecoPiezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Notas Call anytime, day or night MY-HOME1-800-469-4663