Zenoah HTZ2401, HTZ2401L, CHTZ2401, CHTZ2401L manual Manual, If Someone Comes, Maintenance

Page 14

English

5. For safe operation

the manual.

1.Grip the handles firmly with both hands using your whole hand. Place your feet slightly apart (slightly further apart than the width of your shoulders) so that your weight is distributed evenly across both legs, and always be sure to maintain a steady, even posture while working.

2.Keep cutting attachment below waist level.

3.Maintain the speed of the engine at the level required to perform cutting work, and never raise the speed of the engine above the level necessary.

4.If the unit starts to shake or vibrate, turn off the engine and check the whole unit. Do not use it until the trouble has been properly corrected.

5.Keep all parts of your body away from rotating cutting attachment and hot surfaces.

6.Never touch the muffler, spark plug, or other metallic parts of the engine while the engine is in operation or immediately after shutting down the engine. Doing socould result in serious burns or electrical shock.

7.While operating the machine be always sure of a safe and secure operating position especially when using steps or a ladder.

• IF SOMEONE COMES

1.Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris.

2.If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around.

■MAINTENANCE

1.In order to maintain your product in proper working order, perform the maintenance and checking operations described in the manual at regular intervals.

2.Always be sure to turn off the engine before performing any maintenance, checking procedures or working on the machine.

(1) Check ok!

WARNING

The metallic parts reach high temperatures immediately after stopping the engine.

14

Image 14

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido Model HTZ2401 HTZ2401L CHTZ2401 SpecificationsParts location CHTZ2401LEspecificaciohes Emplacement des pieces Situación de las piezasFiche technique Modelo HTZ2401 HTZ2401L CHTZ2401Symbols on the machine Emission ControlControl DE Emisiones EmplacementPosición Information Importante Concernant LE MoteurWorking Circumstance For safe operationWorking Condition Condición DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail Circunstancias DE TrabajoWorking Plan Before Starting the EnginePlan DE Trabajo Plan DE TravailAvant DE Mettre LE Moteur EN Marche Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineArranque DE LA Máquina Demarrage DU MoteurUtilisation DE LA Machine Empleo DEL ProductoIf Someone Comes MaintenanceManual SI SE Acerca Alguien SI QUELQU’UN S’APPROCHEEntretien MantenimientoTransportation Handling FuelRefill after cooling the engine Llenar una vez que el motor se haya enfriado Manipulation DU Carburant Manejo DEL CombustibleTransport TransporteRecommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilFuel Lors de l’utilisation de la véritable huile Zenoah Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS Cutting head will start rotating upon the engine starts OperationStarting Engine Fonctionnement Uso Demarrage DU Moter Arranque DEL MotorRunning in the Engine Adjusting Idling SpeedStopping Engine OP3 Air filterReglage DU Ralenti Arret DU Moteur Apagado DEL MotorFonctionnement DU Moteur Asentamiento DEL MotorDo not press the throttle during this operation HOW to USEHandle CHTZ2401 only Handle Locking leverProcedure Dutilisation Manette CHTZ2401 Cómo UsarHorizontal cut Hedge Trimming TechniquesVertical cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoFuel Filter Replacement Plug is NGK CMR7H or Champion RZ7CAIR Filter Spark PlugEntretien Mantenimiento Intake AIR Cooling Vent BladesLames Ouïe DE Refroidissement PAR AIRVentilación DE Refrigeración DEL Aire DE Admisión AffûtageReduction Gearbox Procedures to be Performed After Every 100 Hours of USEStorage Reducteur Procedures a Effectuer Toutes LES 100 Heures D’UTILISATIONRangement Almacenamiento Caja DE EngranajesGuide de localisation des pannes Troubleshooting guide10. Guía de localización y solución de problemas Nota RemarqueParts list HTZ2401-L Cutting Unit CHTZ2401 S/N CHTZ2401-L S/N CHTZ2401-L Engine Unit HTZ2401/CHTZ2401 HTZ2401-L/CHTZ2401-L S/N Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC