Zenoah HTZ2401, HTZ2401L, CHTZ2401, CHTZ2401L manual Maintenance Chart

Page 32

8. Maintenance

English

Maintenance, replacement, or repair of the emission control device and systems may be performed by any non-road engine repair establishment or individual.

■MAINTENANCE CHART

				Every	Every	Every
	System/components	Procedure		25	50	100	Note
	System/components	Procedure	Before	hours	hours	hours	Note
			Before	hours	hours	hours
			use	after	after	after

	fuel leaks, fuel spillage	wipe out	✔
	fuel tank, air filter, fuel filter	inspect/clean	✔	✔			replace, if necessary
ENGINE	idle adjusting screw	see adjusting	✔				replace carburetor
	idle adjusting screw	idling speed	✔				if necessary
		idling speed					if necessary
	spark plug	clean and readjust			✔		GAP : 0.6 ~ 0.7 mm
	spark plug	plug gap			✔		replace, if necessary
		plug gap					replace, if necessary
	cylinder fins, intake air cooling vent	clean		✔
	muffler, spark arrester, cylinder exhaust port	clean			✔
	throttle lever, ignition switch	check operation	✔
SHAFT	cutting parts	replace if	✔
	cutting parts	something’s wrong	✔
		something’s wrong
	gear case	grease			✔
	screws/nuts/bolts	tighten/replace	✔			✔	not adjusting screws
	screws/nuts/bolts	tighten/replace	✔			✔	not adjusting screws
	debris guard	make sure to attach	✔

32

Image 32

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido Specifications Parts locationModel HTZ2401 HTZ2401L CHTZ2401 CHTZ2401LEmplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Modelo HTZ2401 HTZ2401L CHTZ2401Symbols on the machine Emission ControlEmplacement PosiciónControl DE Emisiones Information Importante Concernant LE MoteurWorking Circumstance For safe operationWorking Condition Consignes de securite Instrucciones de seguridad Conditions DE TravailCondición DE Trabajo Circunstancias DE TrabajoWorking Plan Before Starting the EnginePlan DE Travail Avant DE Mettre LE Moteur EN MarchePlan DE Trabajo Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineDemarrage DU Moteur Utilisation DE LA MachineArranque DE LA Máquina Empleo DEL ProductoIf Someone Comes MaintenanceManual SI QUELQU’UN S’APPROCHE EntretienSI SE Acerca Alguien MantenimientoTransportation Handling FuelRefill after cooling the engine Manipulation DU Carburant Manejo DEL Combustible TransportLlenar una vez que el motor se haya enfriado TransporteRecommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilFuel Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile Zenoah Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFor Your Engine LIFE, Avoid HOW to MIX FuelFueling the Unit Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS Cutting head will start rotating upon the engine starts OperationStarting Engine Fonctionnement Uso Demarrage DU Moter Arranque DEL MotorAdjusting Idling Speed Stopping Engine OP3Running in the Engine Air filterArret DU Moteur Apagado DEL Motor Fonctionnement DU MoteurReglage DU Ralenti Asentamiento DEL MotorHOW to USE Handle CHTZ2401 onlyDo not press the throttle during this operation Handle Locking leverProcedure Dutilisation Manette CHTZ2401 Cómo UsarHorizontal cut Hedge Trimming TechniquesVertical cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is NGK CMR7H or Champion RZ7C AIR FilterFuel Filter Spark PlugEntretien Mantenimiento Intake AIR Cooling Vent BladesOuïe DE Refroidissement PAR AIR Ventilación DE Refrigeración DEL Aire DE AdmisiónLames AffûtageReduction Gearbox Procedures to be Performed After Every 100 Hours of USEStorage Procedures a Effectuer Toutes LES 100 Heures D’UTILISATION Rangement AlmacenamientoReducteur Caja DE EngranajesGuide de localisation des pannes Troubleshooting guide10. Guía de localización y solución de problemas Nota RemarqueParts list HTZ2401-L Cutting Unit CHTZ2401 S/N CHTZ2401-L S/N CHTZ2401-L Engine Unit HTZ2401/CHTZ2401 HTZ2401-L/CHTZ2401-L S/N Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC