Zenoah HTZ2401, HTZ2401L, CHTZ2401, CHTZ2401L manual Symbols on the machine, Emission Control

Page 6

 

English

 

 

 

3. Warning labels on the machine

 

 

 

 

 

(1) Read owner's manual before operating this

 

machine.

(1)

(2) Wear head, eye and ear protection.

 

(3) Handling this machine improperly could result

 

in accidents causing serious injury or death.

 

Read this manual carefully and practice using

 

the hedge-trimmer until you are fully acquainted

(2)

with all operations and have learned to use it

correctly.

 

(4) This is extremely sharp and can easily cause

 

cuts.

 

 

(3)

IMPORTANT

 

 

 

 

If warning label peel off or become soiled and

 

 

impossible to read, you should contact the dealer from

 

which you purchased the product to order new labels

 

and affix them in the required location(s).

(4)

 

 

WARNING

 

 

 

 

 

Never modify your machine.

We won’t warrant the machine, if you use the remodeled hedge-trimmer or you don’t observe the proper usage written in the manual.

4. Symbols on the machine

For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to take a mistake.

(a) The port to refuel the "MIX GASOLINE"

Position:

FUEL TANK CAP

(b) The direction to close the choke

Position:

AIR CLEANER COVER

(c) The direction to open the choke

Position:

AIR CLEANER COVER

■ EMISSION CONTROL

An emission control label is located on the engine.

IMPORTANT ENGINE INFORMATION

THIS ENGINE MEETS U.S. EPA PH2 AND 2006

CALIFORNIA EMISSION REGULATIONS FOR SI

SORE’s. COMPLIANCE PERIOD : CATEGORY A

ENGINE FAMILY : 6KZXS.0244XY ; EM

ENGINE DISPLACEMENT : 24cc

REFER TO OWNER’S MANUAL FOR MAINTE-

NANCE SPECIFICATIONS AND ADJUSTMENTS.

MANUFACTURED:

MADE IN JAPAN

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Model HTZ2401 HTZ2401L CHTZ2401 SpecificationsParts location CHTZ2401LEspecificaciohes Emplacement des pieces Situación de las piezasFiche technique Modelo HTZ2401 HTZ2401L CHTZ2401Symbols on the machine Emission ControlControl DE Emisiones EmplacementPosición Information Importante Concernant LE MoteurFor safe operation Working ConditionWorking Circumstance Condición DE Trabajo Consignes de securite Instrucciones de seguridadConditions DE Travail Circunstancias DE TrabajoWorking Plan Before Starting the EnginePlan DE Trabajo Plan DE TravailAvant DE Mettre LE Moteur EN Marche Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineArranque DE LA Máquina Demarrage DU MoteurUtilisation DE LA Machine Empleo DEL ProductoMaintenance ManualIf Someone Comes SI SE Acerca Alguien SI QUELQU’UN S’APPROCHEEntretien MantenimientoHandling Fuel Refill after cooling the engineTransportation Llenar una vez que el motor se haya enfriado Manipulation DU Carburant Manejo DEL CombustibleTransport TransporteWhen using Zenoah genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Lors de l’utilisation de la véritable huile Zenoah Rapport DE Melange Recommande Essence 50 HuileCarburant Combustible Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteHOW to MIX Fuel Fueling the UnitFor Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS Operation Starting EngineCutting head will start rotating upon the engine starts Fonctionnement Uso Demarrage DU Moter Arranque DEL MotorRunning in the Engine Adjusting Idling SpeedStopping Engine OP3 Air filterReglage DU Ralenti Arret DU Moteur Apagado DEL MotorFonctionnement DU Moteur Asentamiento DEL MotorDo not press the throttle during this operation HOW to USEHandle CHTZ2401 only Handle Locking leverProcedure Dutilisation Manette CHTZ2401 Cómo UsarHedge Trimming Techniques Vertical cutHorizontal cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartTableau D’ENTRETIEN EntretienMantenimiento Tabla DE MantenimientoFuel Filter Replacement Plug is NGK CMR7H or Champion RZ7CAIR Filter Spark PlugEntretien Mantenimiento Intake AIR Cooling Vent BladesLames Ouïe DE Refroidissement PAR AIRVentilación DE Refrigeración DEL Aire DE Admisión AffûtageProcedures to be Performed After Every 100 Hours of USE StorageReduction Gearbox Reducteur Procedures a Effectuer Toutes LES 100 Heures D’UTILISATIONRangement Almacenamiento Caja DE EngranajesTroubleshooting guide 10. Guía de localización y solución de problemasGuide de localisation des pannes Nota RemarqueParts list HTZ2401-L Cutting Unit CHTZ2401 S/N CHTZ2401-L S/N CHTZ2401-L Engine Unit HTZ2401/CHTZ2401 HTZ2401-L/CHTZ2401-L S/N Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC
Top Page Image Contents