Zenoah HTZ2401, HTZ2401L, CHTZ2401, CHTZ2401L Handling Fuel, Refill after cooling the engine

Page 16

English

5. For safe operation

3.When replacing the cutting attachment or any other part, or when replacing the oil or any lubricant, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product.

4.In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance.

5.Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit.

6.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

HANDLING FUEL

1.The engine of the RedMax product is designed to run on a mixed fuel, which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refueling.

(1) Refill after cooling the engine.

4.Wipe spilled fuel completely using a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 3 m or more away from where it was refueled before turning on the engine.

6.Do not inhale fuel fumes as they are toxic.

TRANSPORTATION

1.When hand-carrying the product, cover over the cutting part if necessary, lift up the product and carry it paying attention to the blade.

2.Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport.

16

Image 16
Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Specifications Parts locationModel HTZ2401 HTZ2401L CHTZ2401 CHTZ2401LEmplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes Modelo HTZ2401 HTZ2401L CHTZ2401Symbols on the machine Emission ControlEmplacement PosiciónControl DE Emisiones Information Importante Concernant LE MoteurWorking Condition For safe operationWorking Circumstance Consignes de securite Instrucciones de seguridad Conditions DE TravailCondición DE Trabajo Circunstancias DE TrabajoWorking Plan Before Starting the EnginePlan DE Travail Avant DE Mettre LE Moteur EN MarchePlan DE Trabajo Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineDemarrage DU Moteur Utilisation DE LA MachineArranque DE LA Máquina Empleo DEL ProductoManual MaintenanceIf Someone Comes SI QUELQU’UN S’APPROCHE EntretienSI SE Acerca Alguien MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulation DU Carburant Manejo DEL Combustible TransportLlenar una vez que el motor se haya enfriado TransporteFuel When using Zenoah genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Carburant CombustibleLors de l’utilisation de la véritable huile Zenoah Proporción DE LA Mezcla Recomendada Gasolina 50 AceiteFueling the Unit HOW to MIX FuelFor Your Engine LIFE, Avoid Comment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirEviter Pour Prolonger LA Duree DE VIE DU Moteur Abastecimiento DE LA UnidadFuel Aceite Para USO EN Motores DE 4-TIEMPOS Starting Engine OperationCutting head will start rotating upon the engine starts Fonctionnement Uso Demarrage DU Moter Arranque DEL MotorAdjusting Idling Speed Stopping Engine OP3Running in the Engine Air filterArret DU Moteur Apagado DEL Motor Fonctionnement DU MoteurReglage DU Ralenti Asentamiento DEL MotorHOW to USE Handle CHTZ2401 onlyDo not press the throttle during this operation Handle Locking leverProcedure Dutilisation Manette CHTZ2401 Cómo UsarVertical cut Hedge Trimming TechniquesHorizontal cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartEntretien MantenimientoTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is NGK CMR7H or Champion RZ7C AIR FilterFuel Filter Spark PlugEntretien Mantenimiento Intake AIR Cooling Vent BladesOuïe DE Refroidissement PAR AIR Ventilación DE Refrigeración DEL Aire DE AdmisiónLames AffûtageStorage Procedures to be Performed After Every 100 Hours of USEReduction Gearbox Procedures a Effectuer Toutes LES 100 Heures D’UTILISATION Rangement AlmacenamientoReducteur Caja DE Engranajes10. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Nota RemarqueParts list HTZ2401-L Cutting Unit CHTZ2401 S/N CHTZ2401-L S/N CHTZ2401-L Engine Unit HTZ2401/CHTZ2401 HTZ2401-L/CHTZ2401-L S/N Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty RedMax Garantie limitée Garantía Limitada Komatsu Zenoah America INC