Zenoah CHTZ2401L-CA, CHTZ2401-CA manual Starting the Engine, Using the Product

Page 12

English

5. For safe operation

sufficient to ensure safety.

2.Check the condition of working area to avoid any accident by hitting hidden obstacles such as stumps, stones, cans, or broken glass.

IMPORTANT

Remove any obstacle before beginning work.

3.Inspect the entire unit for loose fasteners and fuel leakage. Make sure that the cutting attachment is properly installed and securely fastened.

■STARTING THE ENGINE

1.Keep bystanders especially children, and animals at least 15 m (50 ft) away from the operating point. If you are approached, immediately stop the engine.

2.The product is equipped with a centrifugal clutch mechanism, so the cutting attachment might begin to rotate as soon as the engine is started. When starting the engine, place the product onto the ground in a flat clear area and hold it firmly in place so as to ensure that neither the cutting part nor the throttle come into contact with any obstacle when the engine starts.

WARNING

Never place the throttle into the high-speed position when starting the engine.

3.After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position. If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit to your authorized RedMax servicing dealer for repair.

■USING THE PRODUCT

IMPORTANT

Cut only materials recommended by the manufacturer. And use only for tasks explained in

12

Image 12

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationModel Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes ModeloSymbols on the machine Emplacement PosiciónFor safe operation Working ConditionWorking Circumstance Conditions DE Travail Condición DE TrabajoCircunstancias DE Trabajo Working Plan Before Starting the EnginePlan DE Travail Avant DE Mettre LE Moteur EN MarchePlan DE Trabajo Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineDemarrage DU Moteur Utilisation DE LA Machine Arranque DE LA MáquinaEmpleo DEL Producto Maintenance ManualIf Someone Comes SI QUELQU’UN S’APPROCHE EntretienSI SE Acerca Alguien MantenimientoHandling Fuel Refill after cooling the engineTransportation Manipulation DU Carburant Manejo DEL Combustible TransportLlenar una vez que el motor se haya enfriado TransporteWhen using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Lors de l’utilisation de la véritable huile RedMax/ZENOAHProporción DE LA Mezcla Recomendada Gasolina 50 Aceite Al utilizar el aceite auténtico de RedMax/ZENOAHHOW to MIX Fuel Fueling the UnitComment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirAbastecimiento DE LA Unidad For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteOperation Starting EngineCutting head will start rotating upon the engine starts Fonctionnement Uso Adjusting Idling Speed Stopping Engine OP3Running in the Engine Air filterArret DU Moteur Apagado DEL Motor Fonctionnement DU MoteurReglage DU Ralenti Asentamiento DEL MotorHOW to USE Handle CHTZ2401/CHTZ2401-CA onlyDo not press the throttle during this operation Handle Locking leverProcedure Dutilisation Manette CHTZ2401/CHTZ2401-CA Cómo UsarHedge Trimming Techniques Vertical cutHorizontal cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is NGK CMR7H or Champion RZ7C AIR FilterFuel Filter Spark PlugFiltre a AIR Filtro DE AireFiltre a Carburant Filtro DE Combustible Bougie D’ALLUMAGE BujíaIntake AIR Cooling Vent BladesOuïe DE Refroidissement PAR AIR Ventilación DE Refrigeración DEL Aire DE AdmisiónLames AffûtageProcedures to be Performed After Every 100 Hours of USE StorageDisposal Reduction GearboxProcedures a Effectuer Toutes LES Heures D’UTILISATION ReducteurCaja DE Engranajes Procedimientos Para Desarrollar Tras Cada 100 Horas DE USOTroubleshooting guide 11. Guía de localización y solución de problemasGuide de localisation des pannes Nota RemarqueParts list Cutting Unit HTZ2401/HTZ2401-CA HTZ2401-L/HTZ2401-L-CA S/N Parts list CHTZ2401-L/CHTZ2401-L-CA Parts list Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control Mesures DE Lutte Contre LES EmissionsControl DE Emisiones HTZ2401/HTZ2401L CHTZ2401/CHTZ2401L