Zenoah CHTZ2401L-CA, CHTZ2401-CA manual Intake AIR Cooling Vent, Blades

Page 36

English

8. Maintenance

MA4

MA5

MA6

leakage is found, stop using the machine and have it repaired immediately.

•Note that failing to do so may result in the engine catching on fire.

■INTAKE AIR COOLING VENT

WARNING

•Never touch the cylinder, muffler, or spark plugs with your bare hands immediately after stopping the engine. The engine can become very hot when in operation, and doing so could result in severe burns.

•Clean the cylinder fins with compressed air or a brush. (MA4)

IMPORTANT

•If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure on the part of the hedge-trimmer.

■BLADES

Oil blades each gas tank filling (MA5).

WARNING

•Make sure that the blade bolts are well tightened.

•The blade assembly is designed to automatically compensate for any play between the blades.

■Sharpening (MA6)

Always keep the file or sharpener at an angle of 45° to the blade, and:

•Always grind in the direction of the cutting edge;

•Note: files cut only in one direction; lift the file from the blade when returning to start a new pass;

•Remove all burr from the edge of the blade with a slip stone;

•Remove as little material as possible;

•Before refitting the sharpened blades, remove filings and then apply grease.

Do not try to sharpen a damaged blade: change it or take it to a Service dealer.

36

Image 36

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOI Tables des matieres ContenidoAdvertencias Contenidas EN EL Manual Specifications Parts locationModel Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes ModeloSymbols on the machine Emplacement PosiciónFor safe operation Working ConditionWorking Circumstance Conditions DE Travail Condición DE TrabajoCircunstancias DE Trabajo Working Plan Before Starting the EnginePlan DE Travail Avant DE Mettre LE Moteur EN MarchePlan DE Trabajo Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineDemarrage DU Moteur Utilisation DE LA Machine Arranque DE LA MáquinaEmpleo DEL Producto Maintenance ManualIf Someone Comes SI QUELQU’UN S’APPROCHE EntretienSI SE Acerca Alguien MantenimientoHandling Fuel Refill after cooling the engineTransportation Manipulation DU Carburant Manejo DEL Combustible TransportLlenar una vez que el motor se haya enfriado TransporteWhen using RedMax/ZENOAH genuine oil FuelRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Lors de l’utilisation de la véritable huile RedMax/ZENOAHProporción DE LA Mezcla Recomendada Gasolina 50 Aceite Al utilizar el aceite auténtico de RedMax/ZENOAHHOW to MIX Fuel Fueling the UnitComment Obtenir UN BON Melange Como Mezclar EL Combustible Remplissage DU ReservoirAbastecimiento DE LA Unidad For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteOperation Starting EngineCutting head will start rotating upon the engine starts Fonctionnement Uso Adjusting Idling Speed Stopping Engine OP3Running in the Engine Air filterArret DU Moteur Apagado DEL Motor Fonctionnement DU MoteurReglage DU Ralenti Asentamiento DEL MotorHOW to USE Handle CHTZ2401/CHTZ2401-CA onlyDo not press the throttle during this operation Handle Locking leverProcedure Dutilisation Manette CHTZ2401/CHTZ2401-CA Cómo UsarHedge Trimming Techniques Vertical cutHorizontal cut Techniques DE Taillage DE Haies Técnicas DE RecorteMaintenance Maintenance ChartTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is NGK CMR7H or Champion RZ7C AIR FilterFuel Filter Spark PlugFiltre a AIR Filtro DE AireFiltre a Carburant Filtro DE Combustible Bougie D’ALLUMAGE BujíaIntake AIR Cooling Vent BladesOuïe DE Refroidissement PAR AIR Ventilación DE Refrigeración DEL Aire DE AdmisiónLames AffûtageProcedures to be Performed After Every 100 Hours of USE StorageDisposal Reduction GearboxProcedures a Effectuer Toutes LES Heures D’UTILISATION ReducteurCaja DE Engranajes Procedimientos Para Desarrollar Tras Cada 100 Horas DE USOTroubleshooting guide 11. Guía de localización y solución de problemasGuide de localisation des pannes Nota RemarqueParts list Cutting Unit HTZ2401/HTZ2401-CA HTZ2401-L/HTZ2401-L-CA S/N Parts list CHTZ2401-L/CHTZ2401-L-CA Parts list Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control Mesures DE Lutte Contre LES EmissionsControl DE Emisiones HTZ2401/HTZ2401L CHTZ2401/CHTZ2401L