Zenoah GZ4500 manual Kickback Safety Precautions for Chain SAW Users

Page 14

English

5. For safe operation

16.Always shut off the engine before setting it down.

17.Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance.

18.When cutting a limb that is under tension, be alert for spring- back so that you will not be struck when the tension in the wood fibers is released.

19.Never cut in high wind, bad weather, when visibility is poor or in very high or low temperatures. Always check the tree for dead branches which could fall during the felling operation.

20.Keep the handles dry, clean and free of oil or fuel mixture.

21.Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide.

22.Do not operate the chain saw in a tree unless specially trained to do so.

23.Guard against kickback. Kickback is the upward motion of the guide bar which occurs when the saw chain at the nose of the guide bar contacts an object. Kickback can lead to dangerous loss of control of the chain saw.

24.When transporting your chain saw, make sure the appropriate guide bar scabbard is in place.

KICKBACK SAFETY PRECAUTIONS FOR CHAIN SAW USERS

WARNING

Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction,kicking the guide bar up and back towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator. Either of these reactions may cause you to Iose control of the saw, which could result in serious personal injury.

Do not rely exclusively on the safety devices built

14

Image 14
Contents GZ4500 Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido Parts location SpecificationsGZ4500 Power unit GZ4500 Groupe moteur Emplacement des pieces Situación de las piezasFiche technique GZ4500Use the chain saw with two hands Read operators instruction book beforeOperating this machine Read, understand and follow all warningsSujete siempre la motosierra con ambas manos Position Oil cap Symbols on the machinePosition Fuel cap Emission ControlInformation Importante Concernant LE Moteur Control DE EmisionesFor safe operation Consignes de securite Instrucciones de seguridad For safe operation Consignes de securite Instrucciones de seguridad Kickback Safety Precautions for Chain SAW Users Consignes de securite Instrucciones de seguridad For safe operation Consignes de securite Instrucciones de seguridad Moving Direction Installing guide bar and saw chainTensioner nut Chain cover Loosen Tighten Tensioner screw Lift upDesserrer Serrer Vis du tendeur Soulever Ecrou de tendeur Carter de chaîneSens de rotation Tuerca del tensor Cubierta de la cadenaInstalling guide bar and saw chain Levante Recommended Mixing Ratio Gasoline 50OIL When using Zenoah genuine oilFuel and chain oil Proporción DE LA Mezcla Recomendada Gasolina 50 Aceite Rapport DE Melange Recommande Essence 50 HuileLors de l’utilisation de la véritable huile Zenoah Al utilizar el aceite auténtico de ZenoahHOW to MIX Fuel Fueling the UnitAbastecimiento DE LA Unidad Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir For Your Engine LIFE, Avoid Chain OILHuile Pour Chaîne Aceite Para LA Cadena Eviter Pour Prolonger LA Duree DE VIE DU MoteurPara Contribuir a LA Vida Útil DEL MOTOR, Evite Starting the Engine Chain oil Fuel Switch Throttle lever Throttle interlockOperation Choke knobBotón del estrangulador ArranqueBouton de starter Checking the OIL Supply Rich Lean Chain oil flow adjustingAdjusting the Carburetor F14 Chain oilAjuste DEL Carburador F14 F14 F15 F16 Needle Idle adjusting screwHow to confirm Needle -1/4 L needle -1/4Frein DE LA Chaîne Freno DE LA CadenaSwitch Carburetor anti-freeze mechanism Stopping the EngineApagado DEL Motor Arrêt DU MoteurInterrupteur Mécanisme antigel de carburateur Interruptor Mecanismo anticongelación del carburadorHOW to Switch Between Operating Modes F19 Choke knob Cylinder cover Icing capFonctionnement Uso F19Sawing Guard Against Kickback F21Mesures DE Protection Contre LES Rebonds F21 Protección Contra Contragolpe F21Felling a Tree F22 Log lying on the ground F23Talado DE Árboles F22 Tronc reposant sur le sol F23Log hanging off the ground F24 Cutting Limb of Fallen Tree F25Elagage d’un arbre F26 Tronc en surélévation F24Ebranchage d’un arbre abattu F25 Un tronco separado del suelo F24Maintenance Maintenance After Each USEEntretien Apres Chaque Utilisation Mantenimiento Después DE Cada USOPeriodical Service Points Entretien Periodique Puntos DE Servicio PeríodicoSprocket Fuel filterNGK CMR7H Filtre à essence Filtro de combustible Filtre à essenceFiltro de combustible Roue dentée Rueda dentadaMaintenance of Saw Chain and Guide Bar SAW ChainNormas para el ajuste de los dientes Méthode et critères d’affûtagePorter des gants de sécurité Avant l’affûtage Guide BAR Ruler Gap No gap Chain tiltsBarra Guía GUIDE-CHAÎNERègle Interstice Pas d’interstice La chaîne est penchéeCase 3. Oil does not come out Troubleshooting GuideCase 2. Lack of power/Poor acceleration/ Rough Idling Cas 1. Défaut de démarrage Guide de dépannage12. Guía para la localización de averías Caso 1. Falla de arranqueAlmacenamiento StorageRangement GZ4500 NotaGZ4500 Cylinder Assy Parts list ARM Carbburetor Components S/N 600101 and up Accessories S/N 600101 and up Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioChain Saws Limited Warranty RedMax Garantie limitée des tronçonneuses Garantía Limitada DE LAS Motosierras Page Page Komatsu Zenoah America INC