Bostitch CAP1645-OF Maintenance Chart, Procedure Daily Weekly, Checking Safety Valve

Page 12

3. Remove hose and accessory.

Risk of unsafe operation. Firmly grasp air hose in hand when installing or discon- necting to prevent hose whip.

4.Drain the air tank, see Draining Air Tank under Maintenance. Ensure air tank pressure gauge reads 0 psi.

Risk of bursting. Drain air tank daily. Water will condense in air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture.

5.Allow the compressor to cool down.

6.Wipe air compressor clean and store in a safe, non-freezing area.

Risk of unsafe operation. Do not operate in vertical position. Vertical position is for storage only.

MAINTENANCE

The following procedures must be followed when maintenance or service is performed on the air compressor.

1.Ensure Auto/Off switch is in the OFF position.

2.Remove air compressor plug from outlet.

3.Drain air tank.

4.Allow air compressor to cool down before starting service.

All compressed air systems contain maintenance parts (e.g., oil, filters, separa- tors) that are periodically replaced. These used parts may contain substances that are regulated and must be disposed of in accordance with local, state, and federal laws and regulations.

NOTE: Take note of the positions and locations of parts during disassembly to make reassembly easier.

NOTE: Any service operations not included in this section should be performed by a BOSTITCH factory service center or a BOSTITCH authorized service center

MAINTENANCE CHART

Procedure

Daily

Weekly

See tank warning

label

 

 

 

Check safety valve

X

 

 

Inspect Air Filter (J)

 

X

 

 

 

 

 

Drain air tank

X

 

 

 

 

 

 

Check for unusual noise/vibration

X

 

 

Check for air leaks

X1

 

 

Clean compressor exterior

 

X

 

Remove tank from service

 

 

X2

1 - To check for air leaks apply a solution of soapy water around joints. While compressor is pumping to pressure and after pressure cuts out, look for air bubbles to form.

2 - For more information, call 1-800-556-6696.

CHECKING SAFETY VALVE

Risk of bursting. If the Safety Valve (G) does not work properly, over-pressuriza- tion may occur, causing air tank rupture or an explosion.

Risk from flying objects. Always wear certified safety equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3) with side shields when using the compressor.

Before starting compressor, pull the ring on the Safety Valve (G) to make sure that the Safety Valve (G) operates freely.Before starting compressor, pull the ring on the Safety Valve (G) to make sure that the Safety Valve (G) operates freely.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Guide Dutilisation Manual DE Instrucciones Important Safety Introduction Definitions Safety GuidelinesResult in property damage Risk of Explosion or FireRisk to Breathing Asphyxiation Risk of BurstingModifications or attempted repairs to the air tank Drain air tank daily or after each useAttachments & accessories TiresRisk of Electrical Shock Risk from Flying ObjectsRisk of HOT Surfaces Risk from Moving PartsRisk of Unsafe Operation Specifications Features Save These Instructions for Future USEComponents FIG End of each use. See Draining Air Tank under Maintenance Installation AssemblyGrounding Instructions FIG USE AN AdapterVoltage and Circuit Protection Compatibility LocationFrom the outlet Transporting FIGPRE-START Checklist FIG Stop when tank pressure reaches cut‑out pressurePreparation for USE START-UP FIGMaintenance Maintenance ChartProcedure Daily Weekly Checking Safety ValveAccessories Service InformationDraining AIR Tank FIG Checking AIR Filter ElementFull ONE Year Warranty GlossaryRepairs Troubleshooting Guide Problem CodeTroubleshooting Codes Possible Cause Possible Solution Risk of bursting. Do not drill into, weldRefer to Motor Overload Protection under Features Introducción La mort ou des blessures gravesRisque D’EXPLOSION OU D’INCENDIE CE QUI Peut SE Produire Comment L’ÉVITERCe qui peut se produire Accessoires  Risque D’ÉCLATEMENTRisque DE Choc Électrique CE QUI Peut SE Produire Comment L’ÉVITERRisque Provenant DES Installer un extincteur dans la zone de travail Son utilisationFiche Technique Poignées coulissantes Manocontacteur Filtre d’admission d’airRégulateur Robinet de purge CaractéristiquesCette pression est contrôlée par le Régulateur F Assemblage FIG La terre’UTILISEZ PAS UN Adaptateur Provoquer UN Choc ÉlectriqueEmplacement Quelle nexcède pas 50 pi 15,2 mProtection DE LA Tension ET DU Circuit CompatibilitéMode D’EMPLOI Déplacementfig BLEVAGEFIG.3A Ranger le compresseur en position verticale ou horizontaleProcédures DE Fonctionnement EntretienDémarrage FIG Arrêt FIGProgramme D’ENTRETIEN Se reporterProcédure Vérification DE LA Soupape DE SûretéAccessoires Vérification DES Éléments DU Filtre D’AIR FIGInformation SUR LES Réparations RéparationsGlossaire Guide DE DépannageProblème Codes DE Dépannage Cause ProbableClapet obstrué DéclenchéAvec un centre de réparation en usine de La pression du réservoirInstrucciones Importantes DE Seguridad Definiciones Normas DE SeguridadGuarde Estas Instrucciones Riesgo DE Explosión O Incendio ¿QUÉ Puede SUCEDER?Riesgo Respiratorio Asfixia ¿QUÉ Puede SUCEDER? Riesgo DE Explosión Tanque de aire y ocasionar la explosión violenta del mismoModificaciones o intento de reparación del tanque de aire Elementos y accesoriosRiesgo DE Descarga Eléctrica ¿QUÉ Puede SUCEDER? Cómo EvitarloRiesgo DE Objetos Despedidos ¿QUÉ Puede SUCEDER? Riesgo DE Superficies Calientes Cómo EvitarloRiesgo POR Piezas Móviles Cómo Evitarlo Mantenga el cabello, la ropa y los guantesRiesgo DE Operación Insegura ¿QUÉ Puede SUCEDER? Otras personasRiesgo DE Caídas Cómo Evitarlo Riesgo POR RuidosEspecificaciones ModeloPresión del sonido KpA = 3,0 dBA re 20μPA LwA = 92,0 dBA re 1 pwPotencia del sonido KwA = 3,0 dBA re 1 pw Componentes FIGVálvula DE Seguridad Válvula DE ControlManómetro Medidor DE Presión DEL Tanque Manómetro Medidor DE Presión DE SalidaInstalación EnsamblajePuede Provocar UNA Descarga Eléctrica Cables ProlongadoresVoltaje Y Protección DEL Circuito CompatibilidadLugar EléctricasPreparación Para EL USO Levantar LA Unidad aTrasladar LA Unidad B Guarde el compresor en posición horizontal o verticalMantenimiento Puesta EN Marcha FIGApagado FIG Posición vertical es sólo para almacenamientoTabla DE Mantenimiento ProcedimientoPara mayor información, llame al Controlar LA Válvula DE Seguridad FIGControlar EL Elemento DEL Filtro DE Aire FIG AccesoriosInformación DEL Servicio Técnico ReparacionesExcepciones Garantía Completa DE UN AÑOCULIACAN, SIN GUADALAJARA, JALMEXICO, D.F MERIDA, YUCCguía DE Detección DE Problema ProblemaGlosario Códigos DE Detección DE Problemas Piezas internas del PinturaInflamable Fusible quemado

CAP1645-OF specifications

The Bostitch CAP1645-OF is a robust and efficient air compressor designed for a variety of applications, including construction, woodworking, and home improvement projects. As a lightweight and portable unit, it packs a powerful punch while making it easy for users to transport and maneuver in different settings.

One of the standout features of the CAP1645-OF is its oil-free pump technology. This innovation eliminates the need for regular maintenance associated with oil-lubricated compressors, making it an ideal choice for DIY enthusiasts and professionals alike. This oil-free design not only reduces the upkeep but also allows for cleaner air output, making it suitable for indoor use without worrying about oil stains or residue.

The unit is equipped with a powerful 1.6 horsepower motor that delivers a maximum pressure of 145 PSI, providing a reliable source of air for various pneumatic tools. This high-pressure capability ensures that users can tackle a range of tasks, from inflating tires and powering nailers to running air tools efficiently. The CAP1645-OF features a 6-gallon pancake-style tank, which enhances stability during operation and allows for efficient air storage.

Moreover, the compressor boasts an impressive recovery time, ensuring that users do not have to wait long between tasks. The low noise level is another notable characteristic; the CAP1645-OF operates at around 78.5 dBA, making it one of the quieter options in its class. This feature is particularly beneficial in environments where noise reduction is necessary, such as residential neighborhoods.

The design of the compressor includes user-friendly controls, making it easy to adjust the pressure settings. The integrated handle and rubber feet enhance portability and stability, respectively. Additionally, the quick-connect air fitting allows for swift tool changes, ensuring that users can maximize productivity without the hassle of fumbling with connections.

Overall, the Bostitch CAP1645-OF stands out for its blend of performance, portability, and user-friendly features. With its oil-free technology, robust motor, and quiet operation, it represents a reliable choice for both professionals and DIY enthusiasts looking to accomplish their air-powered tasks effectively. Whether you are framing, roofing, or simply inflating, the CAP1645-OF is well-equipped to meet your needs.
Top Page Image Contents