Bostitch CAP1645-OF owner manual Draining AIR Tank FIG, Checking AIR Filter Element, Accessories

Page 13

NOTE: Ring may be difficult to pull when air tank pressure is at 0 psi. If the valve is stuck or does not operate smoothly, it must be replaced with the same type of valve.

DRAINING AIR TANK (FIG. 1)

Risk of unsafe operation. Risk from noise. Air tanks contain high pressure air. Keep face and other body parts away from outlet of drain. Use eye protection [ANSI Z87.1 (CAN/ CSA Z94.3)] when draining as debris can be kicked up into face.

Risk from noise. Always wear proper hearing protection during use. Under some conditions and duration of use, noise from this product may contribute to hearing loss.

NOTE: All compressed air systems generate condensate that accumulates in any drain point (e.g. tanks, filter, aftercoolers, dryers). This condensate contains lubricating oil and/or sub- stances which may be regulated and must be disposed of in accordance with local, state, and federal laws and regulations.

Risk of bursting. Drain air tank daily. Water will condense in air tank. If not drained, water will corrode and weaken the air tank causing a risk of air tank rupture.

Risk of Property Damage. Drain water from air tank may contain oil and rust,

which can cause stains.

1.Ensure Auto/Off switch is in the OFF position.

2.Lift compressor into an inclined position so drain valve (M) is at the lowest point (this will assist in removing moisture, dirt, etc. from air tanks).

3.Place a suitable container under the Drain Valve (M) to catch discharge.

4.Grasp lever on Drain Valve (M).

5.Slowly rotate lever to gradually bleed air from air tank.

6.When air Tank Pressure Gauge (K) reads 10 psi, rotate valve to the fully open position.

7.Close Drain Valve (M) when finished.

CHECKING AIR FILTER ELEMENT (FIG.1)

Hot surfaces. Risk of burn. Outlet tube, pump head, and surrounding parts are very hot, do not touch. Allow compressor to cool prior to servicing.

1.Ensure Auto/Off switch (L) is in the OFF Position.

2.Allow unit to cool.

3.Remove filter cover (J) from base.

4.Remove element from filter base.

5.Place new element back in filter base. Purchase replacement parts from your local dealer or authorized service center. Always use identical replacement parts.

6.Snap filter cover to filter base.

Do not operate without air inlet filter

ACCESSORIES

The use of any other accessory not recommended for use with this tool could be hazardous. Use only accessories rated equal to or higher than the rating of the air compressor.

Recommended accessories for use with your tool are available for purchase from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please contact BOSTITCH Fastening Systems 701 E. Joppa Road Towson, Maryland 21286,call 1-800-556-6696 or visit our website www.BOSTITCH.com.

SERVICE INFORMATION

Please have the following information available for all service calls:

ModelNumber_____________________SerialNumber_______________________________

Date and Place of Purchase ____________________________________________________

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Guide Dutilisation Manual DE Instrucciones Definitions Safety Guidelines Important Safety IntroductionResult in property damage Risk of Explosion or FireRisk of Bursting Risk to Breathing AsphyxiationModifications or attempted repairs to the air tank Drain air tank daily or after each useTires Attachments & accessoriesRisk of Electrical Shock Risk from Flying ObjectsRisk from Moving Parts Risk of HOT SurfacesRisk of Unsafe Operation Specifications Save These Instructions for Future USE FeaturesComponents FIG End of each use. See Draining Air Tank under Maintenance Assembly InstallationGrounding Instructions FIG USE AN AdapterCompatibility Location Voltage and Circuit ProtectionFrom the outlet Transporting FIGStop when tank pressure reaches cut‑out pressure PRE-START Checklist FIGPreparation for USE START-UP FIGMaintenance Chart MaintenanceProcedure Daily Weekly Checking Safety ValveService Information AccessoriesDraining AIR Tank FIG Checking AIR Filter ElementGlossary Full ONE Year WarrantyRepairs Problem Code Troubleshooting GuideTroubleshooting Codes Possible Cause Possible Solution Risk of bursting. Do not drill into, weldRefer to Motor Overload Protection under Features La mort ou des blessures graves IntroducciónRisque D’EXPLOSION OU D’INCENDIE CE QUI Peut SE Produire Comment L’ÉVITERCe qui peut se produire Risque D’ÉCLATEMENT Accessoires CE QUI Peut SE Produire Comment L’ÉVITER Risque DE Choc ÉlectriqueRisque Provenant DES Son utilisation Installer un extincteur dans la zone de travailFiche Technique Filtre d’admission d’air Poignées coulissantes ManocontacteurRégulateur Robinet de purge CaractéristiquesCette pression est contrôlée par le Régulateur F La terre Assemblage FIG’UTILISEZ PAS UN Adaptateur Provoquer UN Choc ÉlectriqueQuelle nexcède pas 50 pi 15,2 m EmplacementProtection DE LA Tension ET DU Circuit CompatibilitéDéplacementfig B Mode D’EMPLOILEVAGEFIG.3A Ranger le compresseur en position verticale ou horizontaleEntretien Procédures DE FonctionnementDémarrage FIG Arrêt FIGSe reporter Programme D’ENTRETIENProcédure Vérification DE LA Soupape DE SûretéVérification DES Éléments DU Filtre D’AIR FIG AccessoiresInformation SUR LES Réparations RéparationsGuide DE Dépannage GlossaireCodes DE Dépannage Cause Probable ProblèmeDéclenché Clapet obstruéAvec un centre de réparation en usine de La pression du réservoirDefiniciones Normas DE Seguridad Instrucciones Importantes DE SeguridadGuarde Estas Instrucciones Riesgo DE Explosión O Incendio ¿QUÉ Puede SUCEDER?Riesgo Respiratorio Asfixia ¿QUÉ Puede SUCEDER? Tanque de aire y ocasionar la explosión violenta del mismo Riesgo DE ExplosiónModificaciones o intento de reparación del tanque de aire Elementos y accesorios¿QUÉ Puede SUCEDER? Cómo Evitarlo Riesgo DE Descarga EléctricaRiesgo DE Objetos Despedidos ¿QUÉ Puede SUCEDER? Riesgo DE Superficies Calientes Cómo EvitarloMantenga el cabello, la ropa y los guantes Riesgo POR Piezas Móviles Cómo EvitarloRiesgo DE Operación Insegura ¿QUÉ Puede SUCEDER? Otras personasRiesgo POR Ruidos Riesgo DE Caídas Cómo EvitarloEspecificaciones ModeloLwA = 92,0 dBA re 1 pw Presión del sonido KpA = 3,0 dBA re 20μPAPotencia del sonido KwA = 3,0 dBA re 1 pw Componentes FIGVálvula DE Control Válvula DE SeguridadManómetro Medidor DE Presión DEL Tanque Manómetro Medidor DE Presión DE SalidaEnsamblaje InstalaciónPuede Provocar UNA Descarga Eléctrica Cables ProlongadoresCompatibilidad Voltaje Y Protección DEL CircuitoLugar EléctricasLevantar LA Unidad a Preparación Para EL USOTrasladar LA Unidad B Guarde el compresor en posición horizontal o verticalPuesta EN Marcha FIG MantenimientoApagado FIG Posición vertical es sólo para almacenamientoProcedimiento Tabla DE MantenimientoPara mayor información, llame al Controlar LA Válvula DE Seguridad FIGAccesorios Controlar EL Elemento DEL Filtro DE Aire FIGInformación DEL Servicio Técnico ReparacionesGarantía Completa DE UN AÑO ExcepcionesGUADALAJARA, JAL CULIACAN, SINMEXICO, D.F MERIDA, YUCProblema Cguía DE Detección DE ProblemaGlosario Códigos DE Detección DE Problemas Pintura Piezas internas delInflamable Fusible quemado

CAP1645-OF specifications

The Bostitch CAP1645-OF is a robust and efficient air compressor designed for a variety of applications, including construction, woodworking, and home improvement projects. As a lightweight and portable unit, it packs a powerful punch while making it easy for users to transport and maneuver in different settings.

One of the standout features of the CAP1645-OF is its oil-free pump technology. This innovation eliminates the need for regular maintenance associated with oil-lubricated compressors, making it an ideal choice for DIY enthusiasts and professionals alike. This oil-free design not only reduces the upkeep but also allows for cleaner air output, making it suitable for indoor use without worrying about oil stains or residue.

The unit is equipped with a powerful 1.6 horsepower motor that delivers a maximum pressure of 145 PSI, providing a reliable source of air for various pneumatic tools. This high-pressure capability ensures that users can tackle a range of tasks, from inflating tires and powering nailers to running air tools efficiently. The CAP1645-OF features a 6-gallon pancake-style tank, which enhances stability during operation and allows for efficient air storage.

Moreover, the compressor boasts an impressive recovery time, ensuring that users do not have to wait long between tasks. The low noise level is another notable characteristic; the CAP1645-OF operates at around 78.5 dBA, making it one of the quieter options in its class. This feature is particularly beneficial in environments where noise reduction is necessary, such as residential neighborhoods.

The design of the compressor includes user-friendly controls, making it easy to adjust the pressure settings. The integrated handle and rubber feet enhance portability and stability, respectively. Additionally, the quick-connect air fitting allows for swift tool changes, ensuring that users can maximize productivity without the hassle of fumbling with connections.

Overall, the Bostitch CAP1645-OF stands out for its blend of performance, portability, and user-friendly features. With its oil-free technology, robust motor, and quiet operation, it represents a reliable choice for both professionals and DIY enthusiasts looking to accomplish their air-powered tasks effectively. Whether you are framing, roofing, or simply inflating, the CAP1645-OF is well-equipped to meet your needs.
Top Page Image Contents