Bostitch CAP1645-OF Preparation for USE, PRE-START Checklist FIG, Start-Up Fig, Shut-Down Fig

Page 11

Store compressor in a vertical or horzitional position.

FIG. 3B

A

B

A

B

PREPARATION FOR USE

Do not operate this unit until you read this instruction manual for safety, operation and maintenance instructions.

PRE-START CHECKLIST (FIG. 1)

1.Ensure the Auto/Off switch (L) is in the OFF position.

2.Plug the power cord into the correct branch circuit receptacle. See Voltage and Circuit Protection under Installation.

3.Ensure air tank is drained, see Draining Air Tank under Maintenance.

4.Ensure the drain valve (M) is closed.

5.Ensure safety valve (G) is functioning properly, see Checking Safety Valve (G) under

Maintenance.

6.Pull the regulator knob (F) out and turn counterclockwise until fully closed. Ensure Regulated Pressure Gauge (D) reads 0 psi. Push knob in to lock in place.

7.Attach hose and accessories. NOTE: Always use a minimum 3/8" (9.5 mm) or greater air hose rated at 300 psi.

Risk of unsafe operation. Firmly grasp air hose in hand when installing or disconnecting to prevent hose whip.

Risk of unsafe operation. Do not use damaged or worn accessories.

Risk of Bursting. Too much air pressure causes a hazardous risk of bursting.

Check the manufacturer’s maximum pressure rating for air tools and accessories. The Regulator

(F)outlet pressure setting must never exceed the maximum pressure rating of the tool or accessory.

OPERATING PROCEDURES

START-UP (FIG. 1)

1.Follow Pre-Start Checklist under Preparation for Use.

Risk of property damage. Do not operate in vertical position. Vertical position is for storage only.

2. Move the Auto/Off switch to the AUTO position and allow tank pressure to build. Motor will

stop when tank pressure reaches cut‑out pressure.

Risk of unsafe operation. Compressed air from the unit may contain water­ con- densation and oil mist. Do not spray un­filtered­ air at an item that could be damaged by moisture. Some air oper­ated­ tools or devic­es­ may require filtered air. Read the instruc­tions­ for the air tool or device.

3. Adjust regulator (F) to desired setting. See Regulator under Features.

SHUT-DOWN (FIG. 1)

1.Move Auto/Off switch (L) to the OFF position. NOTE: If finished using compressor, follow Steps 2–6.

NOTE: When the unit has been turned off, it is normal to hear a short hiss of air being released.

NOTE: Unplug unit when not in use.

2.Pull the regulator knob (F) out and turn counterclockwise until fully closed. Ensure regulated pressure gauge reads 0 psi. Push knob in to lock in place.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Guide Dutilisation Manual DE Instrucciones Risk of Explosion or Fire Important Safety IntroductionDefinitions Safety Guidelines Result in property damageDrain air tank daily or after each use Risk to Breathing AsphyxiationRisk of Bursting Modifications or attempted repairs to the air tankRisk from Flying Objects Attachments & accessoriesTires Risk of Electrical ShockRisk of Unsafe Operation Risk of HOT SurfacesRisk from Moving Parts Specifications Components FIG FeaturesSave These Instructions for Future USE End of each use. See Draining Air Tank under Maintenance USE AN Adapter InstallationAssembly Grounding Instructions FIGTransporting FIG Voltage and Circuit ProtectionCompatibility Location From the outletSTART-UP FIG PRE-START Checklist FIGStop when tank pressure reaches cut‑out pressure Preparation for USEChecking Safety Valve MaintenanceMaintenance Chart Procedure Daily WeeklyChecking AIR Filter Element AccessoriesService Information Draining AIR Tank FIGRepairs Full ONE Year WarrantyGlossary Risk of bursting. Do not drill into, weld Troubleshooting GuideProblem Code Troubleshooting Codes Possible Cause Possible SolutionRefer to Motor Overload Protection under Features Comment L’ÉVITER IntroducciónLa mort ou des blessures graves Risque D’EXPLOSION OU D’INCENDIE CE QUI Peut SE ProduireCe qui peut se produire Risque D’ÉCLATEMENT Accessoires Risque Provenant DES Risque DE Choc ÉlectriqueCE QUI Peut SE Produire Comment L’ÉVITER Son utilisation Installer un extincteur dans la zone de travailFiche Technique Caractéristiques Poignées coulissantes ManocontacteurFiltre d’admission d’air Régulateur Robinet de purgeCette pression est contrôlée par le Régulateur F Provoquer UN Choc Électrique Assemblage FIGLa terre ’UTILISEZ PAS UN AdaptateurCompatibilité EmplacementQuelle nexcède pas 50 pi 15,2 m Protection DE LA Tension ET DU CircuitRanger le compresseur en position verticale ou horizontale Mode D’EMPLOIDéplacementfig B LEVAGEFIG.3AArrêt FIG Procédures DE FonctionnementEntretien Démarrage FIGVérification DE LA Soupape DE Sûreté Programme D’ENTRETIENSe reporter ProcédureRéparations AccessoiresVérification DES Éléments DU Filtre D’AIR FIG Information SUR LES RéparationsGuide DE Dépannage GlossaireCodes DE Dépannage Cause Probable ProblèmeLa pression du réservoir Clapet obstruéDéclenché Avec un centre de réparation en usine deRiesgo DE Explosión O Incendio ¿QUÉ Puede SUCEDER? Instrucciones Importantes DE SeguridadDefiniciones Normas DE Seguridad Guarde Estas InstruccionesRiesgo Respiratorio Asfixia ¿QUÉ Puede SUCEDER? Elementos y accesorios Riesgo DE ExplosiónTanque de aire y ocasionar la explosión violenta del mismo Modificaciones o intento de reparación del tanque de aireRiesgo DE Superficies Calientes Cómo Evitarlo Riesgo DE Descarga Eléctrica¿QUÉ Puede SUCEDER? Cómo Evitarlo Riesgo DE Objetos Despedidos ¿QUÉ Puede SUCEDER?Otras personas Riesgo POR Piezas Móviles Cómo EvitarloMantenga el cabello, la ropa y los guantes Riesgo DE Operación Insegura ¿QUÉ Puede SUCEDER?Modelo Riesgo DE Caídas Cómo EvitarloRiesgo POR Ruidos EspecificacionesComponentes FIG Presión del sonido KpA = 3,0 dBA re 20μPALwA = 92,0 dBA re 1 pw Potencia del sonido KwA = 3,0 dBA re 1 pwManómetro Medidor DE Presión DE Salida Válvula DE SeguridadVálvula DE Control Manómetro Medidor DE Presión DEL TanqueCables Prolongadores InstalaciónEnsamblaje Puede Provocar UNA Descarga EléctricaEléctricas Voltaje Y Protección DEL CircuitoCompatibilidad LugarGuarde el compresor en posición horizontal o vertical Preparación Para EL USOLevantar LA Unidad a Trasladar LA Unidad BPosición vertical es sólo para almacenamiento MantenimientoPuesta EN Marcha FIG Apagado FIGControlar LA Válvula DE Seguridad FIG Tabla DE MantenimientoProcedimiento Para mayor información, llame alReparaciones Controlar EL Elemento DEL Filtro DE Aire FIGAccesorios Información DEL Servicio TécnicoGarantía Completa DE UN AÑO ExcepcionesMERIDA, YUC CULIACAN, SINGUADALAJARA, JAL MEXICO, D.FGlosario Cguía DE Detección DE ProblemaProblema Códigos DE Detección DE Problemas Fusible quemado Piezas internas delPintura Inflamable

CAP1645-OF specifications

The Bostitch CAP1645-OF is a robust and efficient air compressor designed for a variety of applications, including construction, woodworking, and home improvement projects. As a lightweight and portable unit, it packs a powerful punch while making it easy for users to transport and maneuver in different settings.

One of the standout features of the CAP1645-OF is its oil-free pump technology. This innovation eliminates the need for regular maintenance associated with oil-lubricated compressors, making it an ideal choice for DIY enthusiasts and professionals alike. This oil-free design not only reduces the upkeep but also allows for cleaner air output, making it suitable for indoor use without worrying about oil stains or residue.

The unit is equipped with a powerful 1.6 horsepower motor that delivers a maximum pressure of 145 PSI, providing a reliable source of air for various pneumatic tools. This high-pressure capability ensures that users can tackle a range of tasks, from inflating tires and powering nailers to running air tools efficiently. The CAP1645-OF features a 6-gallon pancake-style tank, which enhances stability during operation and allows for efficient air storage.

Moreover, the compressor boasts an impressive recovery time, ensuring that users do not have to wait long between tasks. The low noise level is another notable characteristic; the CAP1645-OF operates at around 78.5 dBA, making it one of the quieter options in its class. This feature is particularly beneficial in environments where noise reduction is necessary, such as residential neighborhoods.

The design of the compressor includes user-friendly controls, making it easy to adjust the pressure settings. The integrated handle and rubber feet enhance portability and stability, respectively. Additionally, the quick-connect air fitting allows for swift tool changes, ensuring that users can maximize productivity without the hassle of fumbling with connections.

Overall, the Bostitch CAP1645-OF stands out for its blend of performance, portability, and user-friendly features. With its oil-free technology, robust motor, and quiet operation, it represents a reliable choice for both professionals and DIY enthusiasts looking to accomplish their air-powered tasks effectively. Whether you are framing, roofing, or simply inflating, the CAP1645-OF is well-equipped to meet your needs.
Top Page Image Contents