Subaru Robin Power Products R1200 One M6 x 12 bolt, ’Governor Remove the governor lever j Lever

Page 47

	Sequence1Partto j			Description	Precautions	Necessary
I				I
I		- remove	!			tools
	20	i Muffler	j (1)	Remove the muffler cover ’		:lO m/m box
		Icover	!	from the muffler by taking		ispanner
			i	out the three M6 x 8 flange
			i	bolts.

21 Muffler I(1) Remove the muffler from

	the cylinder section of
	the crank case by taking
	out the two M8 nuts and
I	one M6 x 12 bolt.
I

Brace nuts

I

112m/m box ’spanner

10 m/m box jspanner

M6x12 Bolt, Cross Recess

	I	Part to	1				Description
Sequence	j	remOve					Description	,
								,
22	’Governor		l-(1) Remove the governor lever j
		lever and		from the governor shaft, by:
	!its related			taking			out one M6 x 25	I
	iparts			bolt.				i
				(2) Remove the governor and
				the	.	rod spring from the
					.		.
			I	carburetor
			I

Muffler

Precautions

The bolt has only to be loosened.

Cover

nge Bolt (3 PCS.)

’Necessary tools

110m/m box Ispanner or

j10 m/m spanner

I

I

Governor Lever

Image 47

Contents Rozh -J &ii Foreword Contents Assembly Items SpecificationsAC Output Power FactorRated 800 W Frequency 50 Hz Voltage 110 Output Max Output MaxUnder no load is approximately from 18V up to Frequency 60 Hz Voltage 12ov DC OutputFeatures CHOKE-RUN-STOP Component IdentificationFunction of Each Component L-5 Camshaft 4CONNECTING ROD and PistonMain Bearing Cover CrankshaftCarburetor AIR CleanerDescription of Main Operations ‘CCVoltage Regulation Under Load Fis Output Waveform Current @ Curr&t @ Operational Limits of the Generator Load Electric Battery Capacity Wire Length II ’ Mj 1 mI Measuring ProceduresPage To Measure Insulation Resist Control Panel L a Functional Check of Each ComponentOne section, replace with Assy 83 AVR Windings, or peripheral temperature Value El 10.7J-z Cleaning of Slip RingResistance Exciting coil At rated rpmDisassembly and Assembly Driver Precautions ToolsPrecautions Nection Description M5 x 8 screws SequenceI Part to remove j IFront cover DescriptionI2 Remove the front cover By unscrewing threeDamage the fuel Pipe Description PrecautionsPart to Sequencej remOve Be careful not toSpanner Part to Sequence, removeLpanner Part to Remove $Ez End cover Description Precautions@ Driver Remove the connector Assembling, be That 1wiringSee Fig. g-3-10 RemOve ’Rear ‘bracket Description’ plastic hammer SequenceI Rpearfito~~ DescriptionPull away the stator cover Siw‘ 13 m/m box Spanner Necessary PrecautionsPart to / Sequencej remove ’ JFront Ibracket Description RemOve I10 m/m box spanner DescriptionPrecautions Necessary Tools Blower i 1 1housingNecessary Precautions . tools @ Driver ’Governor Remove the governor lever j Lever Precautions Bolt has only to be loosenedOne M6 x 12 bolt Brace nuts 112m/m box ’spanner 10 m/m box jspannerCrank case by taking 26 i &cocci*nRemove the starting pully Ignition coil fromRetainer Pull out the intake valve and the exhaust valveNotch Spanner 1spring retainer’s Front and hook ’ the minus driverCrankcase Tappets to distin Guish them from one ISequenceI Part toCamshaft Description Remove the crankshaft Be careful not to Be careful not to open the joint too wide, or it will breakAssembly Procedure WTolerances of new installed parts Piston and Piston Ring Connecting rod is joined to the piston with the piston pinTappets and Camshaft Connecting RODIntake Valve and Exhaust Valve =53 WV&e h valve guide clearanceBreather Plate and Tappet Cover Cylinder Head Tappet AdjustmentGovernor Lever Ignition PlugIgnition COIL, Exciting COIL, Flywheel and Starting Pulley Speed Control Muffler and Muffler Cover Nut1’7 Recoil Startor Head Cover and Blower HousingFront Bracket Rear Bracket and Stator Brash Holder Bracket Cover Page Front Cover and Element Cover Fuel Pipe ConnectionConnection of Coupler and Plug Secure the side cover with four M 5 x 8 screws Carburetor Schematic Diagram of the Fuel System By-Pass Choke Disassembly and Assembly of Carburetor 184 Safety Precautions Troubleshooting Starting failur Cock is closed Pzlzq L1Ill IISymptoms AIgnition coil ’ \ r?J Hanging posi- tion is not normal Abration 7Symptoms 0Governor system III Seat Case Case there Abnormal Operation Is too much Pour Lubri Been changed Replace Periodically 1Symptoms Voltemeter Stator sub-coil Symptoms LNo DC voltage is output Voltag,eistoo high QParts LSymptoms Symptoms Voltage Is abnormally low Parts Criteria Table For AdjustmentUel con Limit Items Adjustment Criteira Description Tools LT-Tw Wiring DiagramMaintenance Checks and Maintenance for Every 200 Hours Every Month Page Page Issue EMD-GS0095

Related manuals

Manual 18 pages 8.99 Kb