Subaru Robin Power Products R1200 service manual Features

Page 9

2.FEATURES

(1)Weight of this compact generator with excellent portability is 27.5 kg, which means that the generator is the lightest one in this class.

(2)This generator with an excellent high performance engine and a large size 3.51i fuel tank can run continuously for about 4 hours (at the rated load of 50 Hz).

(3)The operating system is concentrated on the front panel, which enables users to easily handle this generator.

(4)Operations of choking, running, and stopping the engine can easily be executed with a notch.

(5)As a circuit breaker based on the push button system is employed in this generator, replacement of a fuse is unnecessary. Troubles which happen in an overload or failure of devices used can easily be resolved.

(6)Direct current for charging batteries can also be taken out.

(7)Simultaneous use of DC is possible even when AC is used. However, total AC output and DC output should be within the range of the rated output.

(8)Voltage fluctuation ratio is below 5% because of employment of AVR (Automatic Voltage Regulator). Accordingly, the stable voltage is always maintained even if the load fluctuates.

(9)Generally maintenance-free or maintenance is easy because the engine, with a transistor ignition system, has an excellent startability and no point is employed in this generator.

(10)An ignition plug with a resistor and a plug cap have been employed to prevent electric wave noises.

-5-

Image 9
Contents Rozh -J &ii Foreword Contents Assembly Items SpecificationsAC Output Power FactorRated 800 W Frequency 50 Hz Voltage 110 Output Max Output MaxUnder no load is approximately from 18V up to Frequency 60 Hz Voltage 12ov DC OutputFeatures CHOKE-RUN-STOP Component IdentificationFunction of Each Component L-5 Main Bearing Cover 4CONNECTING ROD and PistonCrankshaft CamshaftCarburetor AIR CleanerDescription of Main Operations ‘CCVoltage Regulation Under Load Fis Output Waveform Current @ Curr&t @ Operational Limits of the Generator Load Electric Battery Capacity Wire Length II ’ Mj 1 mI Measuring ProceduresPage To Measure Insulation Resist Control Panel L a Functional Check of Each ComponentOne section, replace with Assy 83 AVR Windings, or peripheral temperature Cleaning of Slip Ring ResistanceValue El 10.7J-z Exciting coil At rated rpmDisassembly and Assembly Driver Precautions ToolsPrecautions Nection Description I2 Remove the front cover SequenceI Part to remove j IFront cover DescriptionBy unscrewing three M5 x 8 screwsPart to Sequencej remOve Description PrecautionsBe careful not to Damage the fuel PipePart to Sequence, remove LpannerSpanner @ Driver Remove the connector Assembling, be Remove $Ez End cover Description PrecautionsThat 1wiring Part toSee Fig. g-3-10 RemOve ’Rear ‘bracket DescriptionSequenceI Rpearfito~~ Description Pull away the stator cover’ plastic hammer Siw‘ Necessary Precautions Part to / Sequencej remove ’ JFront Ibracket Description13 m/m box Spanner RemOve I10 m/m box spanner DescriptionPrecautions Necessary Tools Blower i 1 1housingNecessary Precautions . tools @ Driver One M6 x 12 bolt Precautions Bolt has only to be loosenedBrace nuts 112m/m box ’spanner 10 m/m box jspanner ’Governor Remove the governor lever j LeverRemove the starting pully 26 i &cocci*nIgnition coil from Crank case by takingNotch Spanner 1spring retainer’s Pull out the intake valve and the exhaust valveFront and hook ’ the minus driver RetainerISequenceI Part to Camshaft DescriptionCrankcase Tappets to distin Guish them from one Remove the crankshaft Be careful not to Be careful not to open the joint too wide, or it will breakAssembly Procedure WTolerances of new installed parts Piston and Piston Ring Connecting rod is joined to the piston with the piston pinTappets and Camshaft Connecting RODIntake Valve and Exhaust Valve =53 WV&e h valve guide clearanceBreather Plate and Tappet Cover Cylinder Head Tappet AdjustmentIgnition Plug Ignition COIL, Exciting COIL, Flywheel and Starting PulleyGovernor Lever Speed Control Muffler and Muffler Cover Nut1’7 Recoil Startor Head Cover and Blower HousingFront Bracket Rear Bracket and Stator Brash Holder Bracket Cover Page Front Cover and Element Cover Fuel Pipe ConnectionConnection of Coupler and Plug Secure the side cover with four M 5 x 8 screws Carburetor Schematic Diagram of the Fuel System By-Pass Choke Disassembly and Assembly of Carburetor 184 Safety Precautions Troubleshooting Starting failur Cock is closed Pzlzq L1Ill IISymptoms AIgnition coil ’ \ r?J Hanging posi- tion is not normal Abration 7Symptoms 0Governor system III Seat Case Case there Abnormal Operation Is too much Pour Lubri Been changed Replace Periodically 1Symptoms Voltemeter Stator sub-coil Symptoms LNo DC voltage is output Voltag,eistoo high QParts LSymptoms Symptoms Voltage Is abnormally low Parts Criteria Table For AdjustmentUel con Limit Items Adjustment Criteira Description Tools LT-Tw Wiring DiagramMaintenance Checks and Maintenance for Every 200 Hours Every Month Page Page Issue EMD-GS0095
Related manuals
Manual 18 pages 8.99 Kb