Subaru Robin Power Products R1200 Checks and Maintenance for Every 200 Hours Every Month

Page 99

144 CHECKS AND MAINTENANCE FOR EVERY 200 HOURS (EVERY MONTH)

I

Checks and maintenance items

I

Description

(1)Drain oil from the crankcase and replace with new oil (every 100 hours)

(1)Use of contaminated oil will cause rapid abrasion.

I

(2)

E;p the fuel strainer and the fuel

! (2) and (3)

 

 

a

 

Engine

troubles, including power out-

(3)

Regulate ignition plug clearance.

:

put decline, will be caused.

 

 

14-5 CHECKS AND MAINTENANCE FOR EVERY 500 HOURS (SEMI-ANNUALLY)

1

Checks and maintenance items

!

 

Description

(1)Remove the cylinder head and clean away the carbon deposit.

(2)Disassemble the carburetor and clean each component.

~(3) Check and regulate the valve clear- ante.

~(4) Replace the ignition plug.

/ (1) - (4)

Engine troubles such as power output decline will be caused.

I

14-5 CHECKS AND MAINTENANCE FOR EVERY 1000 HOURS (ANNUALLY)

I

Checks and maintenance items

:

Description

(1)Overhaul the engine for cleaning, adjusting, and replacing parts.

(2)Replace brush of the generator.

(3)Check rotor and stator of the gene- rator.

 

(1) Engine troubles such as power output

I

decline will be caused.

 

(2) and (3)

 

Power output will decline.

(4) Replace the fuel pipe.

( (4) Fuel leakage will cause risks such as fire.

14-7 HOW TO STORE THE GENERATOR FOR A LONG PERIOD

(1)Remove the cap of the fuel strainer and open the fuel cock to completely drain fuel in the tank. Then return the cap to the original position and close the fuel cock.

(2)Start the generator and keep it running until it stops (for about 1 - 2 minutes). The fuel is completely consumed and drains the fuel in the carburetor.

(3)Replace the lubricating oil with new oil.

(4)Clean the air cleaner element.

-95-

Image 99
Contents Rozh -J &ii Foreword Contents Assembly Items SpecificationsAC Output Power FactorRated 800 W Frequency 50 Hz Voltage 110 Output Max Output MaxUnder no load is approximately from 18V up to Frequency 60 Hz Voltage 12ov DC OutputFeatures CHOKE-RUN-STOP Component IdentificationFunction of Each Component L-5 Camshaft 4CONNECTING ROD and PistonMain Bearing Cover CrankshaftCarburetor AIR CleanerDescription of Main Operations ‘CCVoltage Regulation Under Load Fis Output Waveform Current @ Curr&t @ Operational Limits of the Generator Load Electric Battery Capacity Wire Length II ’ Mj 1 mI Measuring ProceduresPage To Measure Insulation Resist Control Panel L a Functional Check of Each ComponentOne section, replace with Assy 83 AVR Windings, or peripheral temperature Cleaning of Slip Ring ResistanceValue El 10.7J-z Exciting coil At rated rpmDisassembly and Assembly Driver Precautions ToolsPrecautions Nection Description M5 x 8 screws SequenceI Part to remove j IFront cover DescriptionI2 Remove the front cover By unscrewing threeDamage the fuel Pipe Description PrecautionsPart to Sequencej remOve Be careful not toPart to Sequence, remove LpannerSpanner Part to Remove $Ez End cover Description Precautions@ Driver Remove the connector Assembling, be That 1wiringSee Fig. g-3-10 RemOve ’Rear ‘bracket DescriptionSequenceI Rpearfito~~ Description Pull away the stator cover’ plastic hammer Siw‘ Necessary Precautions Part to / Sequencej remove ’ JFront Ibracket Description13 m/m box Spanner RemOve I10 m/m box spanner DescriptionPrecautions Necessary Tools Blower i 1 1housingNecessary Precautions . tools @ Driver ’Governor Remove the governor lever j Lever Precautions Bolt has only to be loosenedOne M6 x 12 bolt Brace nuts 112m/m box ’spanner 10 m/m box jspannerCrank case by taking 26 i &cocci*nRemove the starting pully Ignition coil fromRetainer Pull out the intake valve and the exhaust valveNotch Spanner 1spring retainer’s Front and hook ’ the minus driverISequenceI Part to Camshaft DescriptionCrankcase Tappets to distin Guish them from one Remove the crankshaft Be careful not to Be careful not to open the joint too wide, or it will breakAssembly Procedure WTolerances of new installed parts Piston and Piston Ring Connecting rod is joined to the piston with the piston pinTappets and Camshaft Connecting RODIntake Valve and Exhaust Valve =53 WV&e h valve guide clearanceBreather Plate and Tappet Cover Cylinder Head Tappet AdjustmentIgnition Plug Ignition COIL, Exciting COIL, Flywheel and Starting PulleyGovernor Lever Speed Control Muffler and Muffler Cover Nut1’7 Recoil Startor Head Cover and Blower HousingFront Bracket Rear Bracket and Stator Brash Holder Bracket Cover Page Front Cover and Element Cover Fuel Pipe ConnectionConnection of Coupler and Plug Secure the side cover with four M 5 x 8 screws Carburetor Schematic Diagram of the Fuel System By-Pass Choke Disassembly and Assembly of Carburetor 184 Safety Precautions Troubleshooting Starting failur Cock is closed Pzlzq L1Ill IISymptoms AIgnition coil ’ \ r?J Hanging posi- tion is not normal Abration 7Symptoms 0Governor system III Seat Case Case there Abnormal Operation Is too much Pour Lubri Been changed Replace Periodically 1Symptoms Voltemeter Stator sub-coil Symptoms LNo DC voltage is output Voltag,eistoo high QParts LSymptoms Symptoms Voltage Is abnormally low Parts Criteria Table For AdjustmentUel con Limit Items Adjustment Criteira Description Tools LT-Tw Wiring DiagramMaintenance Checks and Maintenance for Every 200 Hours Every Month Page Page Issue EMD-GS0095
Related manuals
Manual 18 pages 8.99 Kb