Subaru Robin Power Products R1200 26 i &cocci*n, Remove the starting pully, Ignition coil from

Page 48

1 Part to Sequence1 remove

23

Carburetor

Description

Precautions

I

Necessary

:

1

tools

 

 

 

 

(1) Remove the carburetor

 

I

 

 

from the cylinder section ’

 

1

 

 

of the crankcase.

 

 

 

24

Starting

 

PUllY

25

Flywheel

!

26i &cocci*n

.

I

I

27’ Exciting 1coil

I

(1) Remove the starting pully

jfrom the flywheel, by tak- ing out one M4 nut. Insert a box spanner or socket wrench into the nuts of the flywheel and strongly hit

it with a hammer, thus re- moving the nuts and the

Ispring washer.

(1)Remove the flywheel from the crankshaft .

!

I

i (1) Remove the ignition plug

I

cap from the ignition plug

and the ignition coil from

I

the crank case by taking

I

out two M6 x 25 bolts.

j (1) Remove the two M6x25

I bolts from Crankcase

Never insert such

810m/m box

tools as driver into

spanner or socket

the flywheel.

/wrench.

Hit it in a counter-

!clockwise direction with a hammer.

i Assemble the tool to Flywheel puller pull out the flywheel

magneto as shown in Fig. 9-3-23. To re- move the flywheel turn the central bolt counterclockwise.

Washer built-in bolt 10 m/m box :spanner

Washer built-in bolt / 10 m/m box 1spanner

Spark Plug Cap

Ignition Coil 1

M6 x 25 Bc

Crankcase ,-I---I

/ - A-- l

Flywheel

Flywheel Puller

Carburetor

I

Fig. 9-3-22

Fig. 9-3-23

-44-

Image 48
Contents Rozh -J &ii Foreword Contents Assembly Specifications ItemsPower Factor AC OutputOutput Max Rated 800 W Frequency 50 Hz Voltage 110 Output MaxFrequency 60 Hz Voltage 12ov DC Output Under no load is approximately from 18V up toFeatures Component Identification CHOKE-RUN-STOPFunction of Each Component L-5 4CONNECTING ROD and Piston Main Bearing CoverCrankshaft CamshaftAIR Cleaner Carburetor‘CC Description of Main OperationsVoltage Regulation Under Load Fis Output Waveform Current @ Curr&t @ Operational Limits of the Generator Load Electric Battery Capacity Wire Length Measuring Procedures II ’ Mj 1 mIPage To Measure Insulation Resist Control Panel Functional Check of Each Component L aOne section, replace with Assy 83 AVR Windings, or peripheral temperature Cleaning of Slip Ring ResistanceValue El 10.7J-z At rated rpm Exciting coilDisassembly and Assembly Precautions Tools DriverPrecautions Nection Description SequenceI Part to remove j IFront cover Description I2 Remove the front coverBy unscrewing three M5 x 8 screwsDescription Precautions Part to Sequencej remOveBe careful not to Damage the fuel PipePart to Sequence, remove LpannerSpanner Remove $Ez End cover Description Precautions @ Driver Remove the connector Assembling, beThat 1wiring Part toRemOve ’Rear ‘bracket Description See Fig. g-3-10SequenceI Rpearfito~~ Description Pull away the stator cover’ plastic hammer Siw‘ Necessary Precautions Part to / Sequencej remove ’ JFront Ibracket Description13 m/m box Spanner RemOve DescriptionPrecautions Necessary Tools Blower i 1 1housing I10 m/m box spannerNecessary Precautions . tools @ Driver Precautions Bolt has only to be loosened One M6 x 12 boltBrace nuts 112m/m box ’spanner 10 m/m box jspanner ’Governor Remove the governor lever j Lever26 i &cocci*n Remove the starting pullyIgnition coil from Crank case by takingPull out the intake valve and the exhaust valve Notch Spanner 1spring retainer’sFront and hook ’ the minus driver RetainerISequenceI Part to Camshaft DescriptionCrankcase Tappets to distin Guish them from one Be careful not to open the joint too wide, or it will break Remove the crankshaft Be careful not toAssembly Procedure WTolerances of new installed parts Connecting rod is joined to the piston with the piston pin Piston and Piston RingConnecting ROD Tappets and CamshaftIntake Valve and Exhaust Valve WV&e h valve guide clearance =53Tappet Adjustment Breather Plate and Tappet Cover Cylinder HeadIgnition Plug Ignition COIL, Exciting COIL, Flywheel and Starting PulleyGovernor Lever Speed Control Nut Muffler and Muffler CoverHead Cover and Blower Housing 1’7 Recoil StartorFront Bracket Rear Bracket and Stator Brash Holder Bracket Cover Page Fuel Pipe Connection Front Cover and Element CoverConnection of Coupler and Plug Secure the side cover with four M 5 x 8 screws Carburetor Schematic Diagram of the Fuel System By-Pass Choke Disassembly and Assembly of Carburetor 184 Safety Precautions Troubleshooting Starting failur Cock is closed Pzlzq L1Ill IISymptoms AIgnition coil ’ \ r?J Hanging posi- tion is not normal Abration 7Symptoms 0Governor system III Seat Case Case there Abnormal Operation Is too much Pour Lubri Been changed Replace Periodically 1Symptoms Voltemeter Stator sub-coil Symptoms LNo DC voltage is output Voltag,eistoo high QParts LSymptoms Symptoms Voltage Is abnormally low Parts For Adjustment Criteria TableUel con Limit Items Adjustment Criteira Description Tools Wiring Diagram LT-TwMaintenance Checks and Maintenance for Every 200 Hours Every Month Page Page Issue EMD-GS0095
Related manuals
Manual 18 pages 8.99 Kb