Servis-Rhino RC-12 manual Point Hitch Assembly Installation

Page 41

ASSEMBLY

3-POINT HITCH ASSEMBLY INSTALLATION

(Lift Models Only)

•Raise hitch into position with hoist. Place narrow section of lower hitch between mounting plates on front of mower. Fasten with 1-7/16" pins (item 1) to lower holes and lock with snapper pin (item 2). Asm-FL-0068.

•Attach clevis portion of link bar assembly (item 3) to mounting point on top front of center plate. Attach spacer (item 5) to end of pin (item 4) and fasten with 1/2" bolt (item 6) and lockwasher. Asm-FL-0068.

•Raise hitch with hoist and insert pin (item 7) through slotted end of link bar and top rear hole on hitch assembly. Fasten with snapper pin (item 2). Asm-FL-0068.

•Slide PTO shaft on to gearbox input shaft and align hole in yoke with hole on shaft. Shaft will only attach at one position. It may be necessary to rotate yoke 180°. Fasten with 5/16” bolt and nut. Asm-FL-0069.

•Bolt gearbox shield in place with four 5/8” cap screws, flatwashers, and lockwashers. Asm-FL-0069.

RC12 12-05

Assembly Section 3-5

© 2005 Alamo Group Inc.

ASSEMBLY

Image 41

Contents RC-12 To the Owner/Operator/Dealer Warranty InformationTable of Contents Maintenance Section Safety Section Safety Wait a minute...Save a life Safety Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety RC12 Safety Section STI-3 Safety MPH. STI-6 Maintenance and Service Safety Instructions and Practices Parts Information Concluding Safety Instructions and Practices Instruct PeligroReflect Logo NFS SER PLTName ModelDecal Description Has stopped. P/N RC12 Safety Section Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Before Operating this Machine Owners Responsibilities Safety Instructions Page Assembly Section Shipping Stand Removal Breather Plug InstallationTongue Assembly Installation Assembly Asm-FL-0066 Point Hitch Assembly Installation Attaching Optional Hydraulic Cylinder Attaching Axle Assemblies to Main Wheel BAR TubeOperation Section Operation CAT II-III Q.H OperationPersonal Protective Equipment PPE Operator RequirementsRops and Seat Belt Tractor Safety DevicesTractor Requirements and Capabilities Power Take Off PTO Front End Weight3-Point Hitch Drawbar-Pull Type MowerBoarding the Tractor Getting on and OFF the TractorDismounting the Tractor Starting the Tractor Connecting the Mower to the TractorPull Type Models Setting the MowerLift Type Models Semi-Mount ModelsOperation Leveling Deck Driveline AttachmentDriveline Clearance Shorten the driveline profiles as follows PRE-OPERATION Inspection and ServiceEngagement Check Procedure Mower Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceSGM-10 Operation Driving the Tractor and Implement Starting the Tractor Raising the Mower Brake and Differential Lock SettingDriving the Tractor and Mower Turning ProcedureCrossing Ditches and Steep Inclines Operating the Tractor and Implement Operation Foreign Debris Hazards Bystanders/Passersby PrecautionsEngaging the Power Take Off PTO Operating the Mower PTO RPM and Ground SpeedOperation Shutting Down the Implement OPS-F-0012A Disconnecting the Mower from the TractorTransporting the Tractor and Implement Mower StorageOperation Transporting on Public Roadways OPS-U Hauling the Tractor and Implement Problem Possible Cause Remedy Trouble Shooting GuidePTO RPM Page Maintenance Section Lubrication General MaintenanceRoutine Maintenance Cutter Shaft Blade ReplacementBelt Adjustment and Replacement Pulley Alignment and Removal Maintenance Cutter Shaft and Bearing Removal InstallationCutter Shaft Bearing Removal Mnt-FL-0041 Outer Cutter Shaft Bearing RemovalCutter Shaft Removal TOP Drive Assembly ServicingMnt-FL-0032 Driveline Shield ReplacementDriveline Figure Mnt-FL-0036 Pre-season Check Storing the RC12Rhino Required of the Operator Required of the OwnerRC12 12/05 00726339C Printed U.S.A