Servis-Rhino RC-12 manual Attaching Axle Assemblies to Main Wheel BAR Tube

Page 42

ASSEMBLY

ASSEMBLY

ATTACHING AXLE ASSEMBLIES TO MAIN WHEEL BAR TUBE

Mark desired row spacing with chalk on wheel bar. Keep outer axle assemblies as close to each end of the shredder to balance load and prevent scalping. Fasten axle assemblies (item 1) to wheel bar (item 2) with clamp plate (item 3) and four 3/4" bolts (item 4), lockwashers and nuts (items 5,6). Tighten bolts evenly and progressively torque to 200 ft. lbs. RC12 is shipped standard with two Axle Assemblies.

Attach ratchet screw jack, (Rhino p/n 00554600) between cylinder bracket mount and ear on rear of center plate.

ATTACHING OPTIONAL HYDRAULIC CYLINDER

(P/N 00725933)

Attach clevis end of hydraulic cylinder (item 1) to mount bracket (item 2) and attach barrel end to rear mount on center plate.

RC12 12-05

Assembly Section 3-6

© 2005 Alamo Group Inc.

Image 42
Contents RC-12 Warranty Information To the Owner/Operator/DealerTable of Contents Maintenance Section Safety Section Safety Wait a minute...Save a life Safety Equipment Operation Safety Instructions and Practices Stop Mowing if Passersby are Within 100 Yards Unless Safety Safety RC12 Safety Section STI-3 Safety MPH. STI-6 Maintenance and Service Safety Instructions and Practices Parts Information Concluding Safety Instructions and Practices Peligro ReflectInstruct Name NFS SER PLTLogo ModelDecal Description Has stopped. P/N RC12 Safety Section Safety Safety Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction Before Operating this Machine Owners Responsibilities Safety Instructions Page Assembly Section Breather Plug Installation Tongue Assembly InstallationShipping Stand Removal Assembly Asm-FL-0066 Point Hitch Assembly Installation Attaching Axle Assemblies to Main Wheel BAR Tube Attaching Optional Hydraulic CylinderOperation Section Operation Operation CAT II-III Q.HOperator Requirements Personal Protective Equipment PPETractor Safety Devices Tractor Requirements and CapabilitiesRops and Seat Belt 3-Point Hitch Front End WeightPower Take Off PTO Drawbar-Pull Type MowerGetting on and OFF the Tractor Boarding the TractorDismounting the Tractor Connecting the Mower to the Tractor Starting the TractorLift Type Models Setting the MowerPull Type Models Semi-Mount ModelsOperation Driveline Attachment Leveling DeckDriveline Clearance PRE-OPERATION Inspection and Service Engagement Check ProcedureShorten the driveline profiles as follows Tractor Pre-Operation Inspection/Service Mower Pre-Operation Inspection/ServiceSGM-10 Operation Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock Setting Raising the MowerTurning Procedure Driving the Tractor and MowerCrossing Ditches and Steep Inclines Operating the Tractor and Implement Operation Bystanders/Passersby Precautions Foreign Debris HazardsEngaging the Power Take Off PTO PTO RPM and Ground Speed Operating the MowerOperation Shutting Down the Implement Disconnecting the Mower from the Tractor OPS-F-0012AMower Storage Transporting the Tractor and ImplementOperation Transporting on Public Roadways OPS-U Hauling the Tractor and Implement Trouble Shooting Guide Problem Possible Cause RemedyPTO RPM Page Maintenance Section General Maintenance LubricationRoutine Maintenance Blade Replacement Belt Adjustment and ReplacementCutter Shaft Pulley Alignment and Removal Maintenance Cutter Shaft Bearing Removal Mnt-FL-0041 InstallationCutter Shaft and Bearing Removal Outer Cutter Shaft Bearing RemovalTOP Drive Assembly Servicing Cutter Shaft RemovalDriveline Shield Replacement DrivelineMnt-FL-0032 Figure Mnt-FL-0036 Storing the RC12 Pre-season CheckRhino Required of the Owner Required of the OperatorRC12 12/05 00726339C Printed U.S.A